We will provide a complete set of bottling equipment IS FREE !

All you need is a shop ready for installation draft beer and a stable monthly flow, namely 200 liters of one variety per month. A minimum spillage of a given volume is necessary, as the life of unpasteurized beer is limited.

Device Pegasus designed for foamless filling of beer from kegs into PET bottles. This equipment made it possible to appear on the Russian markets specialized stores selling drinks from kegs. The defoamer allows you to pour beer into a bottle without loss of quality and in a very short period of time. Now there are many different types Pegasi from different manufacturers. Our company uses only time-tested filling devices.

We will provide you with a set of equipment and install it in your store. Installation of equipment is carried out in a false wall or on a column specialized for Pegasus if you use a flow cooler, which are in all bars and restaurants.

The principle of cooling beer in a cooler is as follows: when the tap is opened, the beer starts to flow along a long coil, which is located in the cooler bath, the bath itself is filled with cold water, the temperature of which is set on the cooler and is always maintained. A plus This method of cooling beer is that with an average flow, the beer is always poured into the bottle cold, despite the temperature of the keg itself and the beer in it. Minus the same is that with a very large strait, the beer does not have time to cool and the last buyer in the queue can buy a warm beer. And also when using coolers It is obligatory to install an air conditioner in the place where kegs and coolers are stored (in the "warehouse" behind a false wall), since a lot of heat is released from the coolers and it becomes very hot in the room, especially in summer, which is bad for beer in kegs, it high temperature can turn sour ahead of time validity!

There is another way to sell beer without coolers - cold room installation. This option is increasingly gaining popularity among conscious entrepreneurs!

The principle of cooling beer in the chamber is as follows: All kegs are kept in a refrigerator, the temperature of which is +4C. At the same time, the beer remains the freshest, the yeast that is present in the keg does not multiply, the effect of preserving the beer and its taste characteristics is obtained. Beer from the refrigerator is considered the most delicious. The advantages are obvious. Of the minuses, this is of course the price of the camera, investments when opening a store will be needed more than when installing coolers that we give for use. And also in the chamber there should always be a supply of beer in order to have time to cool down, if there is no supply of cold beer, then there is also a chance to pour warm beer to the buyer.

The choice of whether to install coolers or one chamber in the store is yours! Below you can see photos of different draft beer stores and different ways sales.

It looks like a classic and the very first defoamer that has proven itself the best way(the body can be both metal and plastic):

This is how the Pegasus installation in a false wall looks like, while all the kegs and coolers are located very conveniently behind the wall without interfering with the seller and without worsening appearance trading floor. In this version of the store, the false wall is made of wood:

The same false wall is only made of a metal finished rack, this option is convenient because it is not attached to the floor, it can be moved as needed and when splashed with beer, it is easy to clean:

Back view:

An example of placing Pegasus in a rack (if the owner likes a small area of ​​\u200b\u200bthe store or this option is more like this):

At the same time, please note that kegs and coolers are under the counter and will prevent the seller from pouring beer, as well as the noise from the coolers will be more audible on the trading floor:

If you do not want to use flow coolers, but want the beer to always be cold in the keg itself, then you can put a refrigerator in the store:

View inside the chamber (such a rack is required behind any false wall, it will save you space):

The same example of a refrigerator, only with the installation of pegasus in two rows:

Technical characteristics of equipment for bottling beer "Pegasus":

• Productivity of the device (depends on temperature of beer) 45-120 l/hour or 60 bottles/hour. That is, the lower the temperature of the beer in your keg or in the cooler, the faster you will pour it through the Pegasus.
• The pressure of carbon dioxide supplied to the keg and the device is 1.5-3 kg/cm3. This pressure must be set on the reducer, which is mounted on a gas cylinder with carbon dioxide.
• Additional consumption of carbon dioxide during accelerated bottling of beer (depends on the gas pressure in the keg and the intensity of bottling beer) 90-360 l/hour (0.2-0.8 kg/hour). One balloon with carbon dioxide is enough for about 2000 liters (if the beer is bottled not warm!, but cold + 4 + 6C).

Below are photos of flow coolers for dispensing beer and on the right is a photo of a carbon dioxide reducer:

When planning to open a beer bottling store from kegs, be sure to take into account the electricity consumption for the installed equipment, it often happens that landlords do not provide more power in the premises and during installation a large number equipment problems begin, knock out traffic jams, the network can not cope. Our chillers consume between 0.6 and 0.8 kW each. If you are installing a refrigerator, be sure to ask how much your split will consume and only then buy it, making sure that there is enough power.

We offer a complete solution for opening promising beer business – turnkey draft beer store.

Our arsenal includes ready-made solutions of any format, we are short term time we will make the design of your premises - from a small department to a bar, cafe or restaurant.

The most demanded services of our company:

1. Mounting and assembly refrigerator compartment for storing beer in kegs;
2. Assembly bar counter, a canopy for defoamers of the Pegas system, as well as other manufacturers, racks for PET containers and other necessary furniture;
3. Installation of false walls, repair and decoration of the premises (if necessary).
4. Installation and installation of advertising structures, banners;
5. Information - we provide the most complete and objective information about possible risks, choosing the right location, positioning the store, the seasonality of the business. In addition, we transfer a complete package of data on suppliers of beer, snacks, equipment and much more;

The quality of the chamber assembly determines the temperature and shelf life of the goods, and, accordingly, the quality of the drink for your customer!

At the moment when the right location has already been chosen, everyone who wants to open a draft beer store from scratch has a question: “WHERE TO START?”. On this page we will present brief instructions for future entrepreneurs of Krasnoyarsk, Moscow and other Russian cities.

1. Bar counter and furniture for a draft beer shop. The assembly of racks and a bar counter is always the second stage in the case when our company fulfills an order for opening a turnkey draft beer store in Moscow and Krasnoyarsk.

   When the refrigerating chamber for kegs is assembled, it’s time to start installing the facade and assembling furniture: a false wall, a canopy for pegasus, a rack for PET containers and, most importantly, the face of the store - bar counter. When ordering a kit, you get a ready-made solution, which means that everything has standard convenient sizes and you do not need to reinvent the wheel by assembling anything yourself or wait a whole month by ordering a rack from furniture makers. The choice of materials and their texture is wide, and final result depends on your wishes. The beer bar counter is made of solid wood, lining, laminated chipboard.

   The cost of a bar counter and a set of furniture depends on the size and selected material. The term for the manufacture and installation of a bar counter in a draft beer store in Krasnoyarsk or Moscow is 2-3 days.

   The price of a bar counter for a beer shop is from 17,000 to 40,000 rubles (depending on materials and size), including delivery, materials and work.

The video demonstrates the assembly of a beer point for 10 varieties with Pegasus Novotap, metal versions of the famous live beer dispensers. Installation of Pegasus was carried out in a false wall made of chipboard. (Also see the article how to mount Pegasus Novotap in the wall). Coolers made by IMI Cornelius were used as beer coolers.

There was no provision for beer pouring into glasses at this point, and no provision for beer columns.

Beer point installation. Part 1: Pegasus preparation.

Training Pegasov Novotap– contents of the box, assembly pegasus.

Beer point installation. Part 2: Installation of Novotapov in the wall.

Mounting pegasi into the chipboard wall.
Fixing on the back side of the wall with a nut. Fixing the unit for supplying beer and gas.

Beer point installation. Part 3: Connecting beer and gas pipelines. Connection to a beer cooler.

back side false walls. Connecting pipes for gas supply, beer and drainage.
Heating the tube in boiling water. Clamp clamp.
Correct sequence: heating the tube in boiling water for several seconds, fixing the clamp on the tube in right place! , putting the tube on the fitting (pipe), clamping the clamp with tongs.

Connection to beer cooler. Wiring of the beer system with tees.

Beer point installation. Part 4: Connecting to sampling heads and reducer.

Connecting sampling heads (or beer tongs, or connectors). Connecting the reducer (reducing valve).

Intake heads are much more convenient to mount with John Guest connectors (John Guest) instead of standard fittings. The video just shows this version of quick-clamp reusable connections.

Auxiliary materials:

Scheme of installation of beer equipment for bottling beer from kegs (click image to enlarge).

The gas pipeline is shown in blue, the beer pipeline is shown in yellow, the drainage outlet is in brown. Large quantity varieties are mounted by analogy.

1. Cylinder with carbon dioxide
2. Gas supply reducer
3. Beer barrel (keg)
4. Intake head
5. Cooler for beer
6. Beer column
7. Drip tray
8. Defoamer
9. Beer tap
10 Beer Hose
11. Gas hose

Using this equipment installation scheme, in a draft beer store you can install any configuration of the beer system that suits your point of sale in the best way.

Firstly: you should decide whether you will install a false wall in the store to install defoamers in it or give preference to installing a bar counter with subsequent fastening of defoamers in beer columns (towers).
If the area of ​​the retail space and its configuration allow you to install a temporary floor-to-ceiling wall across the premises, then all coolers, gas cylinders and all beer kegs will be located behind this false wall and will not interfere under your feet.
A false wall option is a false panel. She is fastened different ways on a load-bearing wall behind which or under which you will install equipment and kegs.
Very often, a false panel is installed on the front wall of a cold room (the so-called "cool room") and defoamers are already attached to it.
If you prefer design outlet bar counter, which means that the equipment, cylinder and beer kegs will most likely be located directly under the bar counter, or, if possible, will be diverted to the utility room using thermally insulated hoses.

Secondly: it is up to you to decide whether you will use the beer served in the bottle through coolers or the area of ​​the room and the availability of financial possibilities allows you to install a cold room ("cool room").
The cooler delivers beer or any other drink to the defoamer and then to the bottle at a temperature of about 4-5 °C. At the same time, the beer itself is stored in the main room at a normal room temperature of about 20-25 ° C. This mode of storage of beer in kegs is not recommended by manufacturers. Beer in this case is not stored for a long time. There is a risk that it will deteriorate before it is fully implemented.
This risk is significantly reduced if your beer kegs are stored in a cold room at 11-12°C and then, passing through the cooler streams, the beer is served to the customer at a temperature of 4-5°C.
Some owners of live draft beer stores set their cold rooms to 4-5 °C, thus avoiding the need for additional coolers in the system. At the same time, one should competently approach the adjustment of the working pressure of carbon dioxide supply to the system, reducing it to 1-1.5 atmospheres (the specialist installer of beer equipment will tell you the exact value of the gas pressure in the system).

Thirdly: if you decide that you will install a bar counter in your beer store, then you can use two main methods for installing defoamers with this installation scheme.
- DEFOAMERS ARE INSTALLED IN BEER COLUMNS (towers). This is enough cost method, since each beer tower is an additional considerable cost for its purchase, and towers will be needed at the rate of - 2 defoamers per tower - a considerable amount;

- ANTIFOAMERS ARE INSTALLED IN THE BEER BOX mounted on top of the bar. This is a kind of the same false wall, but in miniature.
The cost of manufacturing and installing a beer box is relatively low, since it is made of laminated chipboard, which is not difficult to find on sale in any construction hypermarket. In such a box, based on the distance between the defoamer of at least 130 mm, many cranes can be placed. For example, 10 defoamers can be easily installed in a beer box 1500 mm long. At the same time, all hoses - both beer and gas are hidden from the eyes of buyers behind the walls of the box. Very comfortable and aesthetic solution.

Good afternoon! How much does a franchise cost? If you understand correctly when buying beer, you have equipment for free? Will there be a fridge for bottled beer and a fridge for snacks?

Good afternoon, our franchise is free and there are no payments even after opening and running a business! When buying beer from us, yes, we will install drafting equipment for you and will serve you free of charge. We will be able to provide two refrigerators for Tomsky Piv and Bochkarevsky, these are 2 top-selling factories. You need to buy a medium-temperature display case for fish on your own, either a new one or a used one. Under vacuumed snacks or individually closed packaging, a cold display case is not needed. Call if you have any more questions

Hello, I wanted to know if it is possible to purchase equipment for bottling beer for the Trans-Baikal Territory and for rent

You can buy equipment from us, everything is in stock, prepayment, we will deliver it to the time you specified transport company. We rent equipment only in those regions where we have delivery and a sales representative. In the Trans-Baikal Territory, no. Thank you for your feedback.

Hello! Tell me, please, is there a delivery of draft beer in Ryazan and do you rent equipment?

Hello and thanks for reaching out! Yes, we deliver to Ryazan, as well as rent equipment.

How much does it cost to open a draft beer shop?

Briefly formulate the answer, then at least 300,000 rubles. Read more from exemplary business plan we will write an article (soon).

What taxation system to choose when opening a beer store?

Patent. The most convenient form for today will be a patent. For example, when opening a store in the Kosino area, the cost of an annual patent will be 113,400 rubles, and when opening a pub in the Moscow Region, the amount of taxes per year will be 30,210 rubles.

How can I pay for the goods?

1. cash upon receipt of goods


2. non-cash to the current account of Sberbank or VTB24


3. via company website (coming soon)


4. through Sberbank terminals, through an operator in Sberbank, through Sberbankonline, you can find us in the Suppliers section (coming soon)

How can I order beer in the store?

If you do not work with us, then call, we will conclude an Agreement and we will carry it.

If you are already our client, then there are several ways:

1. Through your sales representative (if you lost the number, you can check by phone +74951518585, tell us your legal name and address of the store)


2. Through managers in the office at +74951518585


3. Through the catalog of our site

What days is beer delivery?

From Monday to Saturday we deliver beer to shops.

Can I buy wholesale beer from you without an organization? What if there are a lot of bottles?

No, but you can call us and ask us to find a beer store near you. (84951518585)

Do you make a fake beer wall and bar counter?

No, we do not, but we can suggest who will do it. Call (84951518585)

What kind of rack and why is it needed when opening a pub?

The rack is made right behind the false wall in order to optimize the storage space, the coolers do not take up space among the kegs and so that the beer routes are the shortest distance, because it is important for us that the beer is cold!

It is made from a bar with a minimum thickness of 50mm. Width 600mm and Height 1000mm, the length is equal to the length of your wall. Coolers are installed on the rack during the installation of beer equipment, so it is important that when our technician arrives, the false wall and the rack are ready!

Do you install bottling equipment?

Yes, we do it for free. You need a false wall or a bar counter, a rack, everything else will be done by our technicians.

Do you provide equipment for a draft beer shop?

Yes, we do, for free. The main condition is the purchase of beer from us, that's all.

We also provide taps for free.

Is it possible to connect a PET keg a second time?

PET kegs can only be connected once. The second time the intake head may no longer be put on the keg, since the fitting is disposable. Connect the keg very carefully without sudden movements, do not knock on the keg and do not apply excessive pressure from the outside.

Is there a delivery of draft beer to Zelenograd?

Yes, there is, see the territory for our delivery in the section.

What can not be used to make a false wall for beer? And what is its width?

The wall into which the Pegasi crash (cranes for the sale of draft beer) must be strong and stable. Do not use drywall, all other materials are applicable.

The minimum thickness of the material must be 10 mm, the maximum 16 mm.

If your design idea for the design of the wall is not included in these parameters, we will come up with something and definitely decide how to mount the taps in your beer wall.

What documents are needed for cooperation with the Beer Capital?

• - Certificate of state registration or Record Sheet;


• - Certificate of tax registration;


• - Lease agreement for commercial premises or Certificate of ownership;


• - Details of the Buyer on a form with a sample of the "first" signature, a seal imprint (if there is a seal);


• - a copy of the passport indicating the place of residence;


• - Licenses (permits) for the sale of strong alcohol (if any);


• - ID codes: (EGAIS);

additionally for legal entities:

• - Charter (including pages indicating the address of the location and powers of the governing bodies);


• - Notification of registration with the tax authority at the actual location (notification of the assignment of a checkpoint), if the legal and actual addresses are different with the EGAIS binding;


• - Extract from the Unified State Register of Legal Entities (no later than one month's limitation period);


• - A document confirming the authority of the head (decision or protocol);


• - Order on appointment to the position of the head (director);


• - Power of attorney for an authorized person (if the Agreement is not signed by the head);

Is it worth buying a beer business?

Yes, only for reasonable money, but better before buying, call us (84951518585) and ask how the store, which is now for sale, was doing, we will tell you (please check with IP or LLC).

In fact, realistically evaluate the value of the property of the store itself, and this is usually cash equipment, a refrigerator and a split system for it, a refrigerated display case for fish, bar equipment, tables, chairs, and other things if any. Be aware that beer pouring equipment is not usually property (we give it for use). Take into account the depreciation of all property and bargain with the seller to a price that is acceptable to you.

Consider important after purchase ready shop live beer to inform its regular customers about the change of owner and future changes. Suddenly, someone stopped going into it, knowing that there was a negligent seller, for example, who knew nothing about beer and could not recommend anything. Better even change the sign, name, let everyone passing by notice.

After all, you will run the beer bottling business in your own way!

Good afternoon! Do you sell non-alcoholic drinks?