Over the past few decades, the center of family entertainment has been television. Once there were very few channels, and there was practically nothing to watch on them. Gradually, technologies improved, new standards appeared, the number of channels increased, and characteristics improved. Bulky cathode ray tube televisions have been replaced by thin plasma panels.

TV can do a lot more than you thought

In parallel with all this, the Internet was actively developing, and television in its usual form began to fade into the background. More and more people began to draw information and watch movies online. Thus, there was a need to radically change something in the television industry. And one of these changes was the invention of smart television - Smart TV.

By and large, with its introduction, the use of television has gone beyond watching TV channels. A large number of modern models have either a wired Internet port or a Wi-Fi module. Now you can go online, watch movies, videos and even TV channels. There are various services that allow you to get all the content from the network.

Many users, having bought such a model, do not know about its network capabilities. Therefore, we will analyze how to connect a TV to the Internet. The settings are different for different manufacturers but the principle is the same for everyone.

Wired connection

Connection via cable is considered the most stable, it does not interfere with any interference. To do this, you will need the actual network cable and router. The only drawback is the need to run the cable across the room. Therefore, if possible, place the access point closer to the TV.

Ethernet cable

Automatic IP acquisition

Usually, the router distributes IP addresses automatically. If you are already using it on a PC, connect the TV and the router via a network cable by plugging one end into the TV connector and the opposite end into the LAN port of the access point. If everything is successful, the system will notify you about the successful connection. In selective cases, the procedure should be started manually. To do this, in the network settings, click "Set up Internet", and wait until the settings are received and saved. Try watching YouTube movies to see if it works.

Manual connection setup

Sometimes it may happen that the connection failed. After connecting the network cable, go to the network settings section. The parameters received from the router should be displayed on the screen. If the Internet does not work with them and you cannot watch movies, use the router's web interface in the "Filtering by MAC address" section to fix a permanent IP for the TV. In the TV settings, select " Manual setting”, dial the data from the router. Save your settings and check if it works.

PowerLine adapters (PLC)

You don't want to spoil appearance rooms after repair, but you can’t place the router closer? Use a pair of PowerLine adapters. With their help, you can connect the TV to the router through the mains without the need to run a cable across the room. Plug one adapter into a power outlet and connect to an access point via a network cable. Plug the other adapter into the second outlet and connect it to the TV already. The required conditions are to be plugged directly into the outlet, not into an extension cord, and that no electrical equipment is connected between the adapters. Among the shortcomings, one can name a rather high price, the average price of one device is at least 1000 rubles.

Wireless connection

Built-in WiFi

Smart TVs are equipped with a Wi-Fi module. To watch movies online, you will not need to run a cable, just deploy a Wi-Fi wireless network at home and make a connection. Go to the TV menu, select "Network settings". After starting the setup wizard, select "Wireless connection", select the Wi-Fi network with the remote control, enter the password and click "Connect". Actually, there is nothing complicated, the whole procedure will take a maximum of a couple of minutes. Again, if for some reason the TV could not pick up the assigned IP, enter it manually according to the analog described in the previous paragraph.

You can also connect to Wi-Fi via WPS. Press the button on the router, mark the corresponding item in the TV menu. You don't have to enter any password, the network will be detected automatically.

External WiFi

Older models may not have built-in Wi-Fi. In this case, you will have to purchase an external adapter. It is not very expensive. Check out the characteristics of the device, since not all models are able to function with all TVs. Such a Wi-Fi adapter looks like a USB flash drive and is inserted into the USB port of the TV. After the system recognizes it, configure the device by analogy with the previous paragraph.

Additional router

How to connect a TV to the Internet if it is not possible to buy a Wi-Fi adapter, and the main router is rather weak and a weak signal reaches the TV? You can expand the connection using an auxiliary router. Buy the cheapest model. Set the main router to automatically assign IP, in the settings of the second one, specify "Dynamic IP". The auxiliary router will act as an amplifier at the same time. After the settings, connect the second Wi-Fi router to the TV via a cable. How to fix it, you already know. After all the installations, watching movies will become very easy.

Conclusion

Now you know how to connect your TV to the Internet. We have reviewed different ways. There is nothing difficult in any of them. Look at your capabilities and features of the location of the equipment. Better and easier to set up modern models with built-in Wi-Fi.

Considering that viewing content will consume a lot of Internet channel resources, take care of tariff plan with high speed, as well as sufficient power of the router. Be sure to properly position the equipment so that nothing interferes with signal reception. If possible, we recommend creating a connection via a cable. This is the most reliable option.

Do you use the Internet on TV? How did you connect it? Share with us in the comments.

To fully answer the question of how to connect a TV to Wi-Fi, you need to find out if the TV has the ability to connect to the network. There are many types of connections, it can be an RJ-45 socket, an integrated Wi-Fi module or an adapter. There are models that are able to support external wireless modules.

Support type WiFi connection

TV can be divided by type of connection into four categories:

1. Built-in WiFi. In this case, everything is simple - the wireless module is integrated into the TV. No secondary technologies for connecting TV to the global network are needed;
2. WiFi adapter support . It is impossible to immediately connect such a device to the Internet. To do this, you need a USB adapter;
3. Availability Network Lan-sockets RJ-45 type. In this case, the socket is connected by cable to the second connector in the router operating in client mode, or to the Lan module - a technology that can receive an Internet connection from Wi-Fi and transmit it via cable. However, this requires setting up a local network between the computer and the TV;
4. Without the above additions, but with an HDMI connector. To connect such TVs to the Internet, you need to buy a set-top box Android Mini PC Box . You can find it in any hardware store, along with the device comes instructions for connecting TV to the global network.

A prerequisite for this type of connection is a connected wifi router, which will give access to the global network.

The connection algorithm is as follows (an example is given on Samsung TVs, but it is also suitable for other release models above 2008):

• Using the remote control, go to the network settings (section "Network"). Next, go to the wireless network subsection;

• A list of found Wi-Fi networks will appear. If you do not know the full name of your network, then you can see it on the modem from the back.

If a password is set on Wi-Fi, a window will appear with the alphabet and the ability to enter from the remote control. Management is carried out with the help of arrows, and is selected with the "OK" key. For more convenient control, you can connect a USB keyboard.

After that, the offline connection should start. If this fails, you need to go to the IP settings and re-confirm the item to automatically obtain an IP address on the TV. To do this, go to the TV settings -> go to the network section and select " Wireless. Next, a window pops up with the parameters of the wireless connection. In the first line select " Receive automatically"(usually in the default settings) and confirm.

If your router does not have a DCHP (automatic acquisition) function, you must assign your own IP address to the TV in the settings. For this:

1. In the same way, we go to the wireless connection settings on the TV;
2. Disable the automatic assignment of an IP address (in the properties set "Manual setting", as in the screenshot below);
3. Enter the values ​​below:

IP address - 192.168.1.2. (you can specify any local value).

Subnet mask It has standard view – 255.255.255.0.

Gateway – 192.168.1.1.

DNS server - 8.8.8.8

Many TVs have a "WPS" item in the network settings. Its task is to automatically configure the connection. However, to use the function, it is necessary that the router supports it (the router must have a “WPS” button):

To carry out automatic tuning, the “WSP” item is selected in the TV menu and the button on the router is held down. After 20-30 seconds, the offline setup should complete.

If the owner has a TV and a router of one Samsung, the One Foot Connection feature is designed to facilitate the connection between devices. To do this, you just need to go to this menu section and wait for an offline connection.

In the absence of a built-in module to support a wireless network and external devices, to gain access to the global network, you can buy a player that supports Smart TV and Wi-Fi. Its task is to receive data from a device connected to global network. TV is connected to the player with a regular cable and acts as a screen.

Connecting a TV to Wi-Fi using a laptop

The entire method described above is based on the owner having wireless access to the global network. But the lack of a Wi-Fi router in the apartment is not uncommon, in this case it will come to the rescue direct connection between TV and laptop. It's no secret that all laptops have an integrated Wi-Fi router that can not only receive a signal, but also distribute it. In order to do this, correct configuration is required.

Important. To distribute the signal, the laptop must be cabled to the router.

To create a distribution, you can use both third-party programs and embedded software. The latter is more stable and does not pose a potential danger to the laptop, so the article will only analyze the method associated with the built-in software.

Private WiFi the network is created like this:

1. Load command line. You can do this by going to the menu Start and in the Utilities subsection. Alternative Method: By Combining Keys WIN+R, open the "Run" window and enter cmd;
2. In the line that opens, enter the following value:

Netsh wlan set hostednetwork mode=allow ssid=My_virtual_WiFi key=Cleep keyUsage=persistent

key – password from the created Wi-Fi network

KeyUsage – parameter responsible for saving the password (if you reconnect to the global network, you will not need to enter a password).

When entering, it is extremely important to observe all gaps and use only Latin characters . The team will not only create a Wi-Fi signal distribution, but also install the necessary driver for the network to function. For to start the distribution, you must register:

netsh wlan start hostednetwork

If the TV does not have an internal and external Wi-Fi router, but has an HDMI type connector, then you can only implement a wireless connection using an Android set-top box. In fact, this is the newest and most advanced way to connect TV to the Internet.

The essence of the method: The set-top box connected by a cable to the TV receives a Wi-Fi signal and transmits it to the TV. The main advantage of the method is simplicity. The set-top box only needs to be turned on, all other settings (they are similar to the settings described above) are performed on the TV.

The Android Mini PC TV is a small PC with USB tethering ports. After connecting, in the TV settings, select the device as a signal source (similarly, as with a Wi-Fi network). After that, the screen will display a large number of icons with standard Android applications.

Connection issues

Unforeseen problems and errors may occur while using the connection. It's all easy to fix!

Restart. Disconnect the TV from the network and reconnect.

If the previous step did not help, then you need to reset Smart service settings hub. Algorithm:

1. We go to the applications section;
2. On the PU, click Tools;
3. In the settings, go to the reset section;
4. Enter the updated pin code - 0000;
5. We are waiting for the end of the reset and agree with all the windows that appear (license agreement).
6. Next, the program is reinstalled with reset parameters.

If these two steps did not help, then you should update the TV software. We go to the menu, then to support and to the subsection "Update software» => update the firmware over the network. We are waiting for the update to finish downloading and use it.

If network access is completely impossible, then you can use external media (for example, a USB flash drive or removable hard drive) to update. To do this, you need to download to a USB flash drive latest version firmware specifically for your TV model.

Another common problem is lack of speed. This occurs due to the fact that the router and the TV are in different rooms (for example, behind two walls). Because of this, stability and communication speed are seriously affected. In such situations, it is recommended to place the router and TV closer to each other.

Video instruction:

The video shows all possible types of connection, and describes in more detail about Wi-Fi adapters for TV. And most importantly, all the ways to connect the TV to a wireless network are clearly shown.

Fortunately, all modern TVs support the ability to connect to the Internet using Wi-Fi. Setting up a wireless connection takes much less time. Possible disadvantages are the relative instability of the connection and the low connection speed compared to cable, but modern Wi-Fi routers have practically solved such problems.

In contact with

Many modern TV models have the function of connecting to the Internet. Moreover, the purchase of models with Smart TV generally loses all meaning if there is no way to connect them to a good high speed internet. Most often, the connection is made via a network cable or Wi-Fi wireless technology. But what about those who do not have either wired Internet or wireless? In such cases, the output seems to be the application USB modem supporting 3G/4G technologies. What is so complicated here and why describe the connection procedure, because, probably, it is enough just to insert the modem into one of the USB connectors on the TV? But no, no matter how smart TVs are, they cannot work directly with USB modems, although it is possible that in the foreseeable future manufacturers will eliminate this drawback as well. In the meantime, users who want to combine the incompatible have to go to tricks and look for sophisticated connection methods.

Internet from USB modem to TV via Wi-Fi router

When using this connection method, you should follow a few tips:

• In the process of choosing a router compatible with a 3G/4G modem, in without fail specify whether it specifically supports the modem model that you have or that you plan to purchase. Such information can be obtained on the page of this device on the official website of the manufacturer.
• Pay attention to connection speed. It should be borne in mind that for the normal functioning of Smart TV and the ability to watch movies from the Internet, a high speed of this very Internet is required, which not every 3G modem can provide. After purchasing the router and completing all the settings necessary for its joint work with a modem, the TV can be connected to the Internet both via cable and Wi-Fi, provided that the TV supports this technology. If desired, through this router it will be possible to connect other devices to the Internet.

Connecting a TV set to the Internet provides many advantages and conveniences: the ability to watch YouTube videos, and not just TV channels, subscribe to streaming media services, etc. As part of the article, we will describe all the options for connecting a TV to the Internet. We will analyze wired and wireless methods for new models, as well as old ones that lack a built-in WI-FI module.

What do you need to connect your TV to the Internet?

Modern TVs are ready for connection, they usually have WI-FI, which can catch a signal from the router, it remains only to set up the system. To implement a wired connection, it is necessary to have a LAN connector into which we connect the cable. If neither one nor the other is available, then you will have to buy a special set-top box or another WI-FI modem, which must be adjusted to function in bridge mode. Read on for detailed instructions on how to do all this.

How to connect the TV to the Internet via Wi-Fi?

If there is a Wi-Fi module, then only a small number of actions will be required from you. The main thing is to know the name of your network and remember the password to it.

Attention! In many models, the control menu is different, but the principle of interaction with it remains the same. Read the instructions carefully and by analogy, you can set up a TV from any manufacturer.

Also remember that with a wireless connection, you will lose a little in data transfer speed. If this is unacceptable, give preference to a cable connection.

If everything is done correctly, after a moment the device should report that the pairing was successful.

If something went wrong, then enter the password again to eliminate the error in writing it. Also restart your router and TV, and then follow the same steps again.

Some TV creators have simplified the task for users and added auto-connection tools. Before running it, check if the router has WPS compatibility. Look at its front and look for the signature "WPS / Reset", if there is, then move on.

1. Go to the control panel of the TV receiver, click on "WPS" and at the same time hold down the "WPS / Reset" button on the router.
2. Wait for a while and remove your finger once the process is complete.

If you have Samsung products (TV and router), then there is probably a “One Foot Connection” function for quickly connecting devices. To start, you just need to launch "One Foot Connection" in the TV settings window.

How to connect the TV to the Internet via cable?

Let's talk about how to do this through a router or directly from the main cable.

Connecting directly

A wired connection won't cut your speed, but you'll need to carefully connect your devices so the cord doesn't get in your way. Also this good way“fasten” the TV to the Internet if there was no pre-installed WI-FI module in the TV receiver. The setting is shown on the example of TV from LG, but in other models the essence is about the same.

You should see a message that the connection is set up. Click done to exit the options window.

Connecting through a router

This is true for those who do not connect directly, but through a router, which is connected with an additional piece of wire to the TV.

The process will end with a confirmation that the network is up and running.

How to connect a regular TV without Smart TV to the Internet?

We hasten to please the owners of old TVs with the fact that you can also connect the Internet to their devices. However, for this you will have to purchase a set-top box on the Android OS or Smart TV. A portable Wi-Fi module, which is a simplified version of a set-top box, or another router is also suitable.

Prefix and module

The first option is more interesting, as it allows a simple TV:

• view video and listen to audio through social networks;
• talk on Skype;
• browse sites, YouTube, channels like Netflix;
• connect a mouse and keyboard;
• install programs.

It connects via HDMI-port, sometimes via USB. If they are not there, then you can connect via AV and VGA. Just before buying, make sure that your model is still capable of working with the console. To do this, it is better to call support or read the instructions.

If everything is fine and you have connected, proceed to the setup. Open "Network - Network Setup: Wireless", and there you will find three pairing options:

• "AP" - if you know the data to enter your network (name and password), then choose this;
• "WPS" - suitable if the router supports WPS (we wrote about the configuration features above);
• "Ad-host" is a slightly different parameter responsible for creating local network between PC and TV for data exchange.

Choose the one that suits, and this will complete the setup.

Connecting through a second router

If you are not interested in the chips described in the previous paragraph, then you can save money by buying not a set-top box, but another router that will cost half as much. Connecting is also easy.

1. Connect it to your TV with a power cord.
2. Switch the router to the "Bridge" mode (read how to do this in the instructions for your particular device).
3. Make the connection according to the same principle that we described before.

It turns out that the router is physically connected to the TV, it receives a signal, transmits it over the wire to old tv and enhances reception. This is also a very good way if you just need to access the Internet.

We have described everything good ways connection of any TVs with the Internet. They are simple, so everyone can handle it with a little time.

TV without Internet access today is perceived as something inferior, outdated, because the global network is a huge repository of multimedia content. However, TV is not a device that is customary to replace with a new one every year. What happens: the owners of "anachronisms", released at a time when no one thought about the Internet on TV, to remain deprived? Not at all. Almost any TV receiver can be connected to the World Wide Web with very few exceptions. And today we'll talk about how to do it.

Smart TV is a TV combined with a computer, and the presence of a network adapter for such a device is a matter of course. Happy owners of smart boxes can even choose how to connect the TV to the Internet - via cable or Wi-Fi. Both of these are quite simple.

Cable connection is possible in two ways: directly and through a router. The first option is used if the TV is the only device in the house with a network adapter or a separate Internet channel is allocated for the TV. The provider's cable is connected directly to the TV's network adapter.

The second option - connecting through a router, is much more common. In this case, the TV becomes one of the members of the local network, where the router is the center and source of the Internet. The cable connects the TV network adapter and the LAN port of the router. No special settings are needed for this, the TV is connected to the router in the same way as a computer.

If your Smart TV is equipped with a Wi-Fi adapter, it needs an access point or Wi-Fi router to connect to the global network.

Connecting and setting up the Internet on Samsung Smart TV

When connecting cable type:

• Connect the TV network adapter and the LAN port of the router using a patch cord (a piece of cable with connectors). The screenshot below shows the back of the TV where the network port is located.

• Using the remote control, let's go to the Smart TV settings, from there - to the "Network" and "Network settings" menus.

• In the "Network Type" section, select "Cable".

• Click the "Connect" button.

After a few seconds, the connection will be established and activated. The TV will receive all network parameters automatically.

When connected wirelessly:

• Let's go to the network settings through the main menu of Smart TV.

• Select the connection type "Wireless".

• Select the access point running on your Wi-Fi router.

• Enter the access point password and click Finish.

After a short time, the connection will be established.

On different models of Samsung smart TVs, the appearance and arrangement of menu items are different, but the principle of connecting to the Internet is the same everywhere.

Connecting and setting up the Internet on Smart TV LG

By wire:

• Establish a physical connection between the router and the TV. The socket for the network cable on LG TVs, like Samsung, is located on the rear panel.
• Use the remote control to enter the TV settings menu and go to the "Network" section.

• Select "Wired Connection (Ethernet)".

• After the connection is established, click "Finish" and exit the menu. Internet is set.

Wireless:

• Enter the network settings through the main menu.
• Select the connection type "Wireless".

• In the list of wireless network connection options, click the "Configure from the list of access points" button.

• Enter the password to connect to your hotspot. Confirm your input and wait a few seconds until the connection is established.

If your Smart TV model and router support WPS connection, you can click the second button in this menu - “Easy installation (WPS mode)”, and then press the same button on the router.

Different LG Smart TVs have slightly different menu interfaces. But the difference between them is not so significant that you can get confused. If you figure out how to connect a TV of one model to the Internet, you can easily do it on another.

Other brands of "smart" TVs - Sony, Toshiba, Philips, etc., connect to the global network in exactly the same way.

How to connect Smart TV to the Internet without a built-in network adapter

There are situations when setting up a wired TV connection to the Internet is not possible, for example, if there are no free ports on the router or the cable does not fit into the interior design. And the device is not equipped with a wireless network card. A removable Wi-Fi adapter that plugs into a USB port will help fix the situation.

Unfortunately, these removable adapters are not universal. They are produced by TV manufacturers themselves and only for devices of their brand, and each device supports a strictly limited range of TV models. With which devices a particular adapter is compatible, should be indicated in technical specifications the last one.

Externally removable wifi adapter resembles a large flash drive or USB modem, but there are models of a different type - in the form of a small box with a cable and an antenna (or without it). The former look more aesthetically pleasing, but the latter catch the wireless signal better, because thanks to the cable they can be moved from place to place and thereby find the best reception area.

Like other Wi-Fi devices, plug-in TV adapters belong to different generations of the IEEE 802.11 standard and operate in different frequency ranges.

Modern standards include IEEE 802.11n and IEEE 802.11ac. Only they support a data transfer rate sufficient to view high-definition video content, and operate in two frequency bands at once - 2.4 GHz and 5 GHz. This means that they are compatible with any Wi-Fi routers, since the majority of the latter broadcast either in one or the other range (less often in both). And for the devices to work together, you need to tune to one common frequency.

In addition, removable Wi-Fi adapters for TV differ in the following parameters:

• signal reception radius. It is important that this value is not less than the distance to the access point.
• transmitter power. It is 30-50-70-100 mW. The lower the power of the device, the higher it should be at the access point, especially if the latter is located at a considerable distance from the TV.
• Support for encryption technologies in WiFi networks. For compatibility with modern devices, the adapter must support WPA and WPA 2 standards, with old ones (generations of the 90s and early 2000s) - WEP.

Connecting to the World Wide Web conventional TV

Regular TVs (non-Smart) do not have network adapters, so simply taking and connecting such a device to the Internet will not work. But it's very easy to get around this limitation. It is enough to connect a special set-top box to the TV - Android TV Box, Apple TV or their equivalent. To the delight of the owners of old TV sets, such set-top boxes are now sold at affordable prices and their choice is very large.

A set-top box (media player) is a compact device that looks like a large flash drive or a plastic box that will not only equip your TV with network interfaces, but also give it other “smart” functions. This is, in fact, a miniature computer with its own processor, memory, operating system and other attributes, the monitor of which is a TV, and the input device is a remote control. By the way, special keyboards and similar mice are produced for set-top boxes, and many of them are compatible with ordinary ones.

TV set-top boxes are distinguished by technical parameters. They, like computers and smartphones, are more and less productive. They have different processors, different amounts of RAM and permanent memory, different interfaces. Such devices can connect to the Internet both by wire and over the air.

Set-top boxes, unlike removable Wi-Fi receivers, are universal, that is, they are compatible with various brands and models of TVs. Only the same connection interface is important for both devices. Usually this is HDMI, less often USB, even less often other types.

Setting up the Internet on a TV with a media player is unlikely to cause difficulties for those who have connected a smartphone or computer to the network at least once. After all, they work for the same operating systems as mobile gadgets from PC: Andriod, iOS, Windows.

How to connect the set-top box to the TV

• Turn off the power of both devices (if the set-top box does not have its own power adapter, then only TV). For reliability, it is better to pull the plugs out of the sockets. The HDMI interface, although it supports hot plugging, in fact often burns out, especially if you connect devices, each of which has its own power source.
• Plug the media player or its cable into the HDMI or USB socket of the TV.
• Turn on devices.
• Using the remote control supplied with the set-top box, go to the menu, and from there - to the network settings.

TV connection to the Internet through an electrical outlet

The technology of data transmission over electrical wires - PLC (PowerLine Communication), has existed for a long time, but is not yet very popular. However, soon, one should expect, its finest hour will come, because with the introduction of the Internet of things and smart home systems, traditional wired communication will be difficult, and the radio air will be oversaturated with information flows. Then the electrical network as a transmission medium will be very useful.

PLC is not an independent technology for connecting to the Internet, it transmits data on the principle of Ethernet cable communication (if you do not take into account the features of transmission over power lines), but it is devoid of its main drawback - the need to lay and mask wires. Places for connecting devices to the network are becoming ordinary electrical sockets, more precisely, special adapters installed in them.

PLC adapters, such as in the picture, are supplied to the Russian, Belarusian and Ukrainian markets by TP-Link, ZyXEL, D-Link and some others. They cost around 1000-5000 rubles (the price depends on the transmission speed to the Ethernet and PowerLine channels, the number of devices in the kit, LAN ports and other options).

For comfortable viewing of high-resolution video, it is optimal to buy a PLC with a transfer rate of 100 Mbit / s.

Connecting such devices is not difficult: the LAN ports of one PLC adapter module and the TV are connected with a patch cord, then the adapter is plugged into a power outlet. The second module is connected to the LAN connector of the router and an outlet near it. After that set up wired Internet on TV in the usual way.