20 3 t GOST 1577 93 transcript. Thick-plate and wide-strip rolled products from high-quality structural steel

(9.1.0 EN) OS: XP/2K3/Vista INTER-STATE STANDARD

TECHNICAL CONDITIONS
INTERSTATE COUNCIL
ON STANDARDIZATION, METROLOGY AND CERTIFICATION
Minsk

Foreword

1 DEVELOPED by the Center for Standardization and Certification of Metal Products, Technical Committee for Standardization TC 120 "Iron, Steel, Rolled Products"

INTRODUCED by Gosstandart Russian Federation

2 ADOPTED by the Interstate Council for Standardization, Metrology and Certification on April 15, 1994 (Report of the Technical Secretariat No. 2)

3 By the Decree of the Committee of the Russian Federation for Standardization, Metrology and Certification dated March 19, 1996 No. 180, the interstate standard GOST 1577-93 was put into effect directly as state standard Russian Federation since January 1, 1997

4 INSTEAD OF GOST Specifications

5 EDITION (January 2002) as amended (IUS 4-99, 1-2000)

the dateintroductions 1997-01-01

1 Scope

This standard applies to hot-rolled thick-plate and wide-strip products made of high-quality structural unalloyed and alloyed steel.

2 Normative references

GOST 8.001-80* State system ensuring the uniformity of measurements. Organization and procedure for conducting state testing of measuring instruments

GOST 8.326-89* State system for ensuring the uniformity of measurements. Metrological certification of measuring instruments

* PR 50.2.009-94 is in force on the territory of the Russian Federation.

GOST 82-70 Universal hot-rolled broadband steel. Assortment

GOST 103-76 Hot-rolled steel strip. Assortment

GOST 535-88 Rolled bars and shapes from carbon steel of ordinary quality. General specifications

GOST 1497-84 (ISO 6892-84) Metals. Tensile test methods

GOST 4543-71 Rolled products from alloyed structural steel. Specifications

GOST 7502-98 Metal measuring tapes. Specifications

GOST 7564-97 Rolled products. General rules sampling, blanks and samples for mechanical and technological tests

GOST 7565-81 (ISO 377-2-89) Cast iron, steel and alloys. Sampling method for determination chemical composition

GOST 7566-94 Steel products. Acceptance, marking, packaging, transportation and storage

GOST 9012-59 (ISO 410-82, ISO 6506-81) Metals. Brinell hardness method

GOST 9045-93 Cold-rolled thin-sheet rolled products from high-quality low-carbon steel for cold stamping. Specifications

GOST 9454-78 Metals. Test method for impact bending at low, room and elevated temperatures

GOST 10243-75 Steel. Method of testing and evaluation of macrostructure

GOST 12344-88 Alloyed and high-alloyed steels. Methods for determining carbon

GOST 12345-2001 Alloy and high alloy steels. Methods for the determination of sulfur

GOST 12346-78 (ISO 439-82, ISO 4829-1-86) Alloy and high alloy steels. Methods for the determination of silicon

GOST 12347-77 Alloyed and high-alloyed steels. Phosphorus determination methods

GOST 12348-78 (ISO 629-82) Alloy and high alloy steels. Methods for determination of manganese

GOST 12350-78 Alloy and high alloy steels. Chromium determination methods

GOST 12351-81 Alloyed and high-alloyed steels Methods for determination of vanadium

GOST 12352-81 Alloy and high alloy steels. Nickel determination methods

GOST 12354-81 Alloy and high alloy steels. Methods for the determination of molybdenum

GOST 12357-84 Alloyed and high-alloyed steels. Methods for the determination of aluminum

GOST 12360-82 Alloyed and high-alloyed steels. Boron determination methods

GOST 14019-80 (ISO 7438-85) Metals. Bend Test Methods

GOST 14192-96 Marking of goods

GOST 14637-89 (ISO 4995-78) Thick rolled products from carbon steel ordinary quality. Specifications

GOST 14959-79 Rolled products from spring carbon and alloy steel. Specifications

GOST 15846-79 Products shipped to the Far North and hard-to-reach areas. Packaging, marking, transportation and storage

GOST 19903-74 Hot-rolled sheet metal. Assortment

GOST 22235-76 Main line freight cars railways gauge 1520 mm. General requirements to ensure safety in the production of loading and unloading and shunting operations

GOST 22536.0-87 Carbon steel and unalloyed cast iron. General requirements for methods of analysis

GOST 22536.1-88 Carbon steel and unalloyed cast iron. Methods for determining total carbon and graphite

GOST 22536.2-87 Carbon steel and unalloyed cast iron. Methods for the determination of sulfur

GOST 22536.3-88 Carbon steel and unalloyed cast iron. Phosphorus determination methods

GOST 22536.4-88 Carbon steel and unalloyed cast iron. Methods for the determination of silicon

GOST 22536.5-87 (ISO 629-82) Carbon steel and unalloyed cast iron. Methods for determination of manganese

GOST 22536.6-88 Carbon steel and unalloyed cast iron. Arsenic determination methods

GOST 22536.7-88 Carbon steel and unalloyed cast iron. Chromium determination methods

GOST 22536.8-87 Carbon steel and unalloyed cast iron. Methods for determining copper

GOST 22536.9-88 Carbon steel and unalloyed cast iron. Nickel determination methods

GOST 22536.10-88 Carbon steel and unalloyed cast iron. Methods for the determination of aluminum

GOST 22727-88 Rolled sheet. Ultrasonic testing methods

GOST 26877-91 Steel products. Methods for measuring shape deviations

GOST 28473-90 Cast iron, steel, ferroalloys, chromium, manganese metal. General requirements for methods of analysis

3 Main parameters and dimensions

3.1 Rolled products are made from steel grades 08kp, 08ps, 08, 10kp, 10ps, 10, 15kp, 15ps, 15, 20kp, 20ps, 20, 25, 30, 35, 40, 45, 50, 55, 60 - according to GOST 1050; 08Yu - according to GOST 9045; 15G, 20G, 30G, 40G, 50G, 10G2, 35G2, 20X, 30X, 38XA, 40X, 45X - according to GOST 4543; 65, 70, 60G, 65G, 70G - according to GOST 14959

Note - Rolled sheets are made from steel grade 08Yu.

(Amendment).

3.2 Rolled products are made with a thickness:

4 - 160 mm - sheet; 4 - 12 mm - roll;

6 - 60 mm - broadband.

3.3 Requirements for the range of rolled products must comply with:

GOST 19903 - for sheet and roll;

GOST 82 - for broadband.

3.4 Symbols for the characteristics of rolled products when placing an order are given in the table Table 1.

Table 1 - Symbols for the characteristics of rolled products

Characteristics of rolled products	Clause number of this standard	Characteristic symbol
Accuracy of rolling according to the thickness of the plate:
increased	Clause 4.2.1
normal	Clause 4.1.1
Broadband length:
random	Clause 4.1.2
	Clause 4.2.2
multiple of dimensional	Clause 4.2.2
Type of rolled flatness:
normal	Clause 4.1.1
improved	Clause 4.2.1; Clause 4.2.2
	Clause 4.2.1
especially high	Clause 4.2.1
Rib curvature broadband grades:
	Clause 4.2.2
	Clause 4.1.2
Edge condition:
unedged	Clause 4.1.1; Clause 4.1.2
Edged	Clause 4.2.3; Clause 4.3.3
Rolled stock delivery status:
Without heat treatment	Clause 4.1.7; Clause 4.2.8; Clause 4.2.11	Not designated
heat treated	Clause 4.2.6; Clause 4.2.7; Clause 4.3.8
Hardness of rolled products up to 80 mm thick incl. as delivered:
Without heat treatment, after controlled rolling, in heat treated condition	Clause 4.1.7; Clause 4.2.7, table Table 2
Without heat treatment and continuous rolling mills with standards for annealed or high tempered steel	Clause 4.2.8, table Table 2
Control of the hardness of rolled products with a thickness of St. 80 mm	Clause 4.3.9
Mechanical properties:
Rolled products up to 80 mm thick incl. as delivered or on standardized blanks	Clause 4.2.9, table Table 3
Plates up to 80 mm thick, supplied without heat treatment or continuous rolling mills, with standards for annealed or high-tempered rolled products	Clause 4.2.10, table Table 3
In the normalized state on blanks with a size determined by the consumer	Paragraph 4.3.10, table Table 5
After seaming with tempering on blanks with a size determined by the consumer	Paragraph 4.3.11, table Table 6
Normalized impact strength at a temperature of minus 20 ° C for rolled products up to 80 mm thick incl.	Clause 4.2.11
Control of impact strength at a temperature of minus 20 °C, minus 40 °C , minus 50 ºС for rolled products from calm steel grades	Clause 4.3.12
Cold bend test	Clause 4.2.12
Normalized in points macrostructure of rolled products with a thickness of more than 10 mm	Clause 4.3.14
Guaranteed decarburization no more than 2% per side	Clause 4.3.7
Descaling	Clause 4.3.15
Deburring of burrs obtained when trimming thick-plate products and cutting broad-strip products to cut-to-length lengths	Clause 4.3.17
Ultrasonic testing of metal continuity	Clause 4.3.13	1UZK, 2UZK, 3UZK
Type of filling in the quality document indicating: - rolled products comply with GOST 1577
All types of tests carried out
Weldability guarantee	Clause 4.3.16

Examples symbols rental are given in Appendix Appendix 1.

(Amendments).

4 Technical requirements

4.1 Characteristics of the basic version

4.1.1 Rolled plate without heat treatment or after controlled rolling, normal accuracy in thickness, normal flatness, with an unedged edge.

4.1.2 Rolled broadband without heat treatment, random length, with edge curvature of class B, normal flatness, with unedged edge.

4.1.3 The chemical composition of steel according to the ladle test and the permissible deviations in the finished rolled products must comply with GOST 1050, GOST 4543, GOST 9045 and GOST 14959.

4.1.4 Surface quality and requirements for rolled edges must comply with GOST 14637.

4.1.5 Stratification in rental is not allowed.

4.1.6 In the macrostructure of rolled products, there should not be delaminations, accumulations of rolled bubbles, slag inclusions and flocs visible without the use of magnifying devices.

4.1.7 The hardness of rolled products with a thickness of up to 80 mm inclusive without heat treatment or after controlled rolling must comply with the standards specified in Table 2.

Table 2 - Hardness of rolled products

steel grade	Without heat treatment or after controlled rolling		Normalized		Annealed or high tempered
steel grade		Hardness HB, no more	Indentation diameter, mm, not less than	Hardness HB, no more	Indentation diameter, mm, not less than	Hardness HB, no more
08kp, 08ps, 08, 08Yu
10kp, 10ps, 10
15kp, 15ps, 15
20kp, 20ps, 20

























Notes 1 Hardness standards for normalized rolled products were not rejected until 01.01.98. 2 The “+” sign means that the hardness control is carried out for the data set and the results of the control are recorded in the quality document.

4.2 Characteristics to be set by the user

4.2.1 Rolled plate with increased accuracy in thickness, flatness - improved, high and extra high according to GOST 19903.

4.2.2 Rolled broadband universal, cut-to-length or multiple cut-to-length, improved flatness, with edge curvature class A according to GOST 82.

4.2.3 Rolled plate with a thickness of up to 80 mm inclusive with a cut edge.

4.2.4 Rental with mass fraction th sulfur 0.020% - 0.035%.

4.2.5 Rolled products with a mass fraction of sulfur and phosphorus, reduced against the standards of GOST 1050, GOST 4543, GOST 9045 and GOST 14959.

4.2.6 Rolled products with a thickness of up to 80 mm inclusive in a heat-treated state (normalized, annealed, high-tempered).

4.2.7 Rolled products with a thickness of up to 80 mm inclusive in a heat-treated state with the requirements for hardness given in Table Table 2.

4.2.8 Rolled products up to 80 mm thick from steel grades 08kp, 08ps, 08, 10kp, 10ps, 10, 15kp, 15ps, 15, 20kp, 20ps and 20 without heat treatment and continuous rolling mills with hardness in accordance with the norms of the table Table 2 for annealed or high tempered steel.

4.2.9 Rolled products with a thickness of up to 80 mm inclusive with mechanical properties in accordance with the requirements given in Table 3.

Table 3 - Mechanical properties of rolled products

steel grade

Rolled plates

Broadband normalized steel or normalized blanks

without heat treatment, after controlled rolling or normalized

annealed or highly tempered

Yield strength σ T N / mm 2 (kgf / mm 2)

Tensile strength σ in, N / mm 2 (kgf / mm 2)

Relative elongation δ 5 %

Yield strength σ T, N / mm 2 (kgf / mm 2)

Tensile strength σ V, N / mm 2 (kgf / mm 2)

Relative elongation δ 5 %

Relative narrowing of the cross section ψ, %

Notes

1 For steel grade 08Yu, the norms apply only to plate rolled products.

2 With a rolled product thickness of more than 20 mm, a decrease in relative elongation by 0.25% abs. for each millimeter of increase in the thickness of rolled products, but not more than 2% for rolled products with a thickness of up to 32 mm inclusive and by 3% for rolled products with a thickness of more than 32 mm.

3 For annealed rolled steel grades 35, 40, 45 and 50, a reduction in tensile strength by 39 N/mm 2 (4 kgf/mm 2) is allowed.

4 "+" sign means that the characteristic is controlled for the data set. The control results are recorded in the quality document.

4.2.10 Rolled products up to 80 mm thick from steel grades 08kp, 08ps, 08, 10kp, 10ps, 10, 15kp, 15ps, 15, 20kp, 20ps and 20 without heat treatment and continuous rolling mills with mechanical properties in accordance with the norms of the table Table 3 for annealed or high tempered steel.

4.2.11 Rolled products without heat treatment, after controlled rolling and normalized with a thickness of up to 80 mm inclusive, from steel grades 10, 15, 20, 15G and 20G with a normalized impact strength KCU of at least 29 J/cm 2 (3 kgf m/cm 2 ) at a temperature of minus 20 °C.

4.2.12 Rolled products with a thickness of up to 60 mm inclusive with a 180 ° cold bending test with a mandrel thickness indicated in table Table 4. At the bend, there should be no break, delamination and cracks visible to the naked eye.

Table 4 - Cold bend test

4.3 Characteristics and standards established by agreement between the consumer and the manufacturer

4.3.1 Rolled products with clarification of the requirements for the assortment in relation to GOST 19903 and GOST 82.

4.3.2 Rolled plates with a length of 1.5 to 5 m.

4.3.3 Rolled plate with a thickness of more than 80 mm with a cut edge.

4.3.4 Rolled products with normalized total mass fraction of sulfur and phosphorate.

4.3.5 Rolled products with a reduced mass fraction of residual elements in steel relative to GOST 1050, GOST 4543, GOST 9045 and GOST 14959.

4.3.6 Rolled products with an increased mass fraction of residual elements (chromium, nickel, copper) in steel smelted by the scrap or scrap ore process, relative to the standards of GOST 1050, GOST 4543, GOST 9045 and GOST 14959.

4.3.7 Rolled steel with a mass fraction of carbon in the brand according to the lower limit of at least 0.3% with a guarantee of a decarburization depth (ferrite + transition zone) of not more than 2% per side of the actual sheet thickness.

4.3.8 Rolled products with a thickness of St. 80 mm in heat treated condition.

4.3.9 Rolled products with a thickness of St. 80 mm with hardness control.

4.3.10 Rolled products with mechanical properties in the normalized state in accordance with the standards specified in the table Table 5.

Table 5 - Mechanical properties of rolled products in a normalized state

steel grade	Thickness, mm	Yield strength σ 0.2, N / mm 2 (kgf / mm 2), not less	Tensile strength σ V, N / mm 2 (kgf / mm 2)	Relative elongation δ 5 %

				rolling directions

			400 - 550 (41 - 56)
	100 to 160		380 - 520 (39 - 53)
			420 - 570 (43 - 58)
	16 to 100		420 - 570 (43 - 58)
	100 to 160		400 - 550 (41 - 56)
			450 - 630 (46 - 64)
	16 to 100		450 - 630 (46 - 64)
	100 to 160		430 - 610 (44 - 62)
			480 - 670 (49 - 68)
	16 to 100		480 - 670 (49 - 68)
	100 to 160		460 - 650 (47 - 66)
			530 - 720 (54 - 73)
	16 to 100		530 - 720 (54 - 73)
	100 to 160		510 - 700 (52 - 71)
			580 - 770 (59 - 79)
	16 to 100		580 - 770 (59 - 79)
	100 to 160		560 - 750 (57 - 76)
			600 - 820 (61 - 84)
	16 to 100		600 - 820 (61 - 84)
	100 to 160		580 - 800 (59 - 82)
			630 - 870 (64 - 89)
	16 to 100		630 - 870 (64 - 89)
	100 to 160		610 - 850 (62 - 89)
			650 - 920 (66 - 94)
	16 to 100		650 - 920 (66 - 94)
	100 to 160		630 - 880 (64 - 90)
Note - The norms of mechanical properties were not rejected until 01.01.98. The control results are recorded in the quality document.

4.3.11 Rolled products with mechanical properties after quenching and tempering in accordance with the standards specified in the table Table 6.

4.3.12 Rolled products from calm steel grades with impact strength control at minus 20 °C, minus 40 °C or minus 50 °C.

4.3.13 Rolled products with ultrasonic continuity testing.

Continuity standards - in accordance with classes 1, 2, 3 according to GOST 22727.

4.3.14 Rolled products with a thickness of more than 10 mm with a macrostructure normalized in points.

4.3.15 Rolled products cleaned from scale. The method of descaling is chosen by the manufacturer.

4.3.16 Rolled products with guarantee of weldability. Weldability is ensured by manufacturing technology and chemical composition.

4.3.17 With deburring.

4.3.18 With sheet-by-sheet testing of the mechanical properties of rolled steel grade 20.

4.3.19 Rolled products by chemical composition.

4.4 Marking of rolled products - according to GOST 7566.

4.4.1 Transport marking - according to GOST 14192.

4.5 Packing, forming packs and bundles of rolled products - according to GOST 7566.

4.5.1 Packaging of rolled products for the regions of the Far North and equivalent regions - in accordance with GOST 15846.

4.5.2 Rolled products cleaned from scale by etching shall be lubricated on both sides with neutral oil or neutral oil with an inhibitor addition.

5 Acceptance rules

5.1 General rules for acceptance of rolled products - according to GOST 7566.

5.2 Rolled products are presented for acceptance in batches.

The batch should consist of sheets of coils or strips of the same steel grade, the same size in thickness, the same heat treatment mode - for heat-treated rolled products, and for rolled products from ingots and CWR - from one melt - ladle.

In batches from continuous casting plants, the difference in the mass fraction of carbon in steel should not exceed 0.04%, and in the mass fraction of manganese - 0.15%.

The mass of a batch poured on a continuous casting plant must not exceed 400 g.

It is allowed to form a batch of rolled products of the basic design from steel of several heats.

5.3 Each batch is accompanied by a quality document in accordance with GOST 7566.

In accordance with the order, the quality document has two types of filling:

With an indication: "Products comply with GOST 1577";

Indicating the results of all types of tests carried out.

Note - If there is no type of quality document in the order, the document is drawn up at the discretion of the manufacturer.

Table 6 - Mechanical properties of rolled products after quenching and tempering

steel grade

For rolled products with thickness, mm

up to 16 incl.

St. 16 to 40

St. 40 to 100

Yield strength σ 0.2, N / mm 2 (kgf / mm 2) not less

Tensile strength σ V, N / mm 2 (kgf / mm 2)

Relative elongation δ 5 %

Relative contraction ψ, %

Tensile strength σ V, N / mm 2 (kgf / mm 2)

Relative elongation δ 5 %

Relative contraction ψ, %

Impact work KV at 20 ºС, J (kgf m)

Yield strength σ 0.2 N / mm 2 (kgf / mm 2)

Tensile strength σ V, N / mm 2 (kgf / mm 2)

Relative elongation δ 5 %

Relative contraction ψ, %

Impact work KV, at 20 ºС J (kgf m)

Notes

1 The results of the control of mechanical properties are optional until 01.01.98.

2 The standards of mechanical properties for rolled steel grade 30 are given for thicknesses up to 63 mm.

3 The sign "+" means that the characteristic is determined for the data set. The results are recorded in the quality document.

5.4 Rolled products are subjected to acceptance tests.

5.5 To check the quality of the batch of rolled products are selected:

1) for chemical analysis - samples according to GOST 7565.

The manufacturer carries out control of the chemical composition on the ladle test, if necessary - in the finished product;

2) for surface quality control - all sheets, rolls and strips;

3) for dimensional control - two sheets, rolls or strips, for sheet rolling - all sheets, rolls or strips;

4) for shape control - two sheets, rolls or strips;

5) to control hardness and mechanical properties, macrostructure, cold bending tests - one sheet, roll or one strip.

When delivering rolled products in a heat-treated state, control sheets are taken from the middle of the charge. During heat treatment of rolled products in continuous thermal furnaces, control sheets are selected at random.

From rolled products made on continuous rolling mills and not requiring heat treatment, samples are taken from the outer coil of the coil.

5.6 It is allowed for a batch of rolled products to apply the results of tests of sheets, coils and strips made of steel of the same heat for macrostructure and mechanical properties obtained on batches of rolled products of large thicknesses, to apply to batches of rolled products of smaller thicknesses.

5.7 Upon receipt of unsatisfactory test results for at least one of the indicators, repeated tests are carried out in accordance with GOST 7566.

6 Test methods

6.1 Chemical analysis of steel is carried out in accordance with GOST 28473, GOST 22536.0 - GOST 22536.10, GOST 12344 - GOST 12352, GOST 12354, GOST 12357, GOST 12360 or other methods that provide the necessary accuracy of determination.

For steel from continuous casting plants, the difference in mass fraction of carbon and manganese in the batch is determined by ladle analysis.

6.2 Geometric dimensions and non-flatness are determined using measuring tools according to GOST 26877, GOST 162, GOST 166, GOST 427, GOST 7502 or tools certified according to GOST 8.001 or GOST 8.326.

The thickness of rolled products is measured at a distance of at least 100 mm from the ends and 40 mm from the edges.

6.3 Sampling for mechanical tests according to Table 3 and technological tests are carried out according to GOST 7564.

Sampling for mechanical tests according to tables Table 5 and Table 6 is carried out in accordance with Appendix Appendix 2.

6.4 The quality of the rolled surface is controlled visually. Rolled products for the absence of bundles are controlled by inspection of the edges and ends without the use of magnifying devices. It is allowed to use devices of the IGT-10NK type or other devices of a similar class. With visual detection of delamination, the quality of rolled products is additionally checked by removing chips. In this case, the bifurcation of the chips is a sign of metal discontinuity.

It is allowed for the consumer to control the absence of delamination after cutting.

6.5 From each sheet, roll or strip selected for inspection:

for tensile and bending tests - one sample each;

for impact bending tests - two samples from rolled products with a thickness of 5 mm or more;

to check the macrostructure - one transverse template 250 mm long from the middle part of the width of the rolled product;

to test the hardness - two samples each: one from the edge, the other from the middle part of the rolled width;

to control the depth of the decarburized layer - one sample from the edge of the width of the rolled product.

6.6 Tensile test is carried out according to GOST 1497.

Specimens for testing the mechanical properties of wide strip (see table Table 3), supplied without heat treatment, are made from normalized billets 25 mm thick. With a strip thickness of less than 25 mm, normalization is carried out on blanks equal to the strip thickness.

6.7 Tensile and impact test specimens (see tables Table 5 and Table 6) are cut from heat-treated blanks in the size specified by the consumer.

6.8 Bending test is carried out in accordance with GOST 14019.

6.10 Impact bending test is carried out in accordance with GOST 9454 on samples of types 1, 2, 3 and 11. The mode of heat treatment of blanks (samples) to determine impact strength at a temperature of minus 20 ºС, minus 40 ºС or minus 50 °С of rolled products from calm steel grades set by agreement between the manufacturer and the consumer.

6.11 Hardness determination is carried out according to GOST 9012.

6.12 The macrostructure control is carried out by the etching method according to GOST 10243. The manufacturer can guarantee the requirements for the macrostructure without control.

The methodology and scales for monitoring the macrostructure of rolled products in thicknesses of more than 10 mm are established by agreement between the manufacturer and the consumer.

6.13 Determination of the depth of the decarburized layer is carried out according to GOST 1763.

6.14 Ultrasonic testing is carried out according to GOST 22727.

6.15 To control the macrostructure, mechanical properties, hardness and decarburized layer, it is allowed to use non-destructive and statistical control methods according to the procedure approved in the prescribed manner.

In technically justified cases, at the request of the consumer, mechanical properties are controlled in accordance with GOST 1497 and GOST 9454.

7 Transport and storage

7.1 Transportation and storage - according to GOST 7566.

7.2 Rolled products are transported by all types of transport in accordance with the rules for the carriage of goods in force for this type of transport.

7.3 When transporting rolled products by rail type of shipment - carload.

Rolled sheets and wide strips of structural quality steel. Specifications

GOST 1577-93

Introduction date 1997-01-01

1 Scope

This standard applies to hot-rolled thick-plate and wide-strip products made of high-quality structural unalloyed and alloyed steel.

2 Normative references

GOST 8.001-80* State system for ensuring the uniformity of measurements. Organization and procedure for conducting state testing of measuring instruments

GOST 8.326-89* State system for ensuring the uniformity of measurements. Metrological certification of measuring instruments

GOST 82-70 Universal hot-rolled broadband steel. Assortment GOST 103-76 Hot-rolled steel strip. Assortment

GOST 535-88 Rolled bars and shapes from carbon steel of ordinary quality. General specifications

GOST 1497-84 (ISO 6892-84) Metals. Tensile test methods GOST 4543-71 Rolled products from alloyed structural steel. SpecificationsGOST 7502-98 Measuring metal tapes. SpecificationsGOST 7564-97 Rental. General rules for sampling, blanks and samples for mechanical and technological tests

GOST 7565-81 (ISO 377-2-89) Cast iron, steel and alloys. Sampling method for determining the chemical composition

GOST 7566-94 Steel products. Acceptance, marking, packaging, transportation and storage

GOST 9012-59 (ISO 410-82, ISO 6506-81) Metals. Brinell hardness method

GOST 9045-93 Cold-rolled thin-sheet rolled products from high-quality low-carbon steel for cold stamping. Specifications

GOST 9454-78 Metals. Test method for impact bending at low, room and elevated temperatures

GOST 10243-75 Steel. Method of testing and evaluation of macrostructure

GOST 12344-88 Alloyed and high-alloyed steels. Methods for determination of carbon GOST 12345-2001 Alloyed and high-alloyed steels. Methods for determination of sulfurGOST 12346-78 (ISO 439-82, ISO 4829-1-86) Alloyed and high-alloyed steels. Methods for the determination of silicon

GOST 12347-77 Alloyed and high-alloyed steels. Phosphorus determination methods

* PR 50.2.009-94 is in force on the territory of the Russian Federation.

GOST 12348-78 (ISO 629-82) Alloyed and high-alloyed steels. Methods for determination of manganese

GOST 12350-78 Alloyed and high-alloyed steels. Methods for the determination of chromium GOST 12351-81 Alloy and high-alloy steels Methods for the determination of vanadiumGOST 12352-81 Alloy and high-alloy steels. Nickel determination methodsGOST 12354-81 Alloyed and high-alloyed steels. Methods for determination of molybdenumGOST 12357-84 Alloyed and high-alloyed steels. Methods for the determination of aluminum

GOST 12360-82 Alloyed and high-alloyed steels. Boron determination methods GOST 14019-80 (ISO 7438-85) Metals. Bend test methodsGOST 14192-96 Cargo marking

GOST 14637-89 (ISO 4995-78) Carbon steel thick plate of ordinary quality. Specifications

GOST 14959-79 Rolled products from spring carbon and alloy steel. Specifications

GOST 15846-79 Products shipped to the Far North and hard-to-reach areas. Packaging, marking, transportation and storage

GOST 19903-74 Hot-rolled sheet metal. Assortment

GOST 22235-76 Freight cars of 1520 mm gauge mainline railways. General requirements for ensuring safety in the production of loading and unloading and shunting operations

GOST 22536.0-87 Carbon steel and unalloyed cast iron. General requirements for methods of analysis

GOST 22536.1-88 Carbon steel and unalloyed cast iron. Methods for determining total carbon and graphite

GOST 22536.2-87 Carbon steel and unalloyed cast iron. Methods for determination of sulfur GOST 22536.3-88 Carbon steel and unalloyed cast iron. Methods for determination of phosphorus GOST 22536.4-88 Carbon steel and unalloyed cast iron. Methods for the determination of silicon

GOST 22536.5-87 (ISO 629-82) Carbon steel and unalloyed cast iron. Methods for determination of manganese

GOST 22536.6-88 Carbon steel and unalloyed cast iron. Methods for determination of arsenic GOST 22536.7-88 Carbon steel and unalloyed cast iron. Methods for determination of chromium GOST 22536.8-87 Carbon steel and unalloyed cast iron. Methods for determining copperGOST 22536.9-88 Carbon steel and unalloyed cast iron. Nickel determination methodsGOST 22536.10-88 Carbon steel and unalloyed cast iron. Methods for the determination of aluminum

GOST 22727-88 Rolled sheet. Methods of ultrasonic testing GOST 26877-91 Steel products. Methods for measuring shape deviations GOST 28473-90 Cast iron, steel, ferroalloys, chromium, manganese metal. General requirements for methods of analysis

3 Main parameters and dimensions

3.1 Rolled products are made from steel grades 08kp, 08ps, 08, 10kp, 10ps, 10, 15kp, 15ps, 15, 20kp, 20ps, 20, 25, 30, 35, 40, 45, 50, 55, 60 - according to GOST 1050; 08YU - according to GOST 9045; 15G, 20G, 30G, 40G, 50G, 10G2, 35G2, 20X, 30X, 38XA, 40X, 45X - according to GOST 4543; 65, 70, 60G, 65G, 70G - according to GOST 14959.

Note - Rolled sheets are made from steel grade 08Yu.

(Amendment).

3.2 Rolled products are made with a thickness:

4 - 160 mm - sheet;

4 - 12 mm - rolled;

6 - 60 mm - broadband.

3.3 Requirements for the range of rolled products must comply with:

GOST 19903 - for sheet and roll;

GOST 82 - for broadband.

3.4 Symbols for the characteristics of rolled products when placing an order are given in Table 1.

Table 1 - Symbols for the characteristics of rolled products

End of table 1

Examples of rental symbols are given in Appendix 1. (Amendments).

4 Technical requirements

4.1 Characteristics of the basic version

4.1.1 Rolled plate without heat treatment or after controlled rolling, normal accuracy in thickness, normal flatness, with unedged edge.

4.1.2 Rolled broadband without heat treatment, random length, with edge curvature of class B, normal flatness, with unedged edge.

4.1.3 The chemical composition of steel according to the ladle test and the permissible deviations in the finished product must comply with GOST 1050, GOST 4543, GOST 9045 and GOST 14959.

4.1.4 Surface quality and requirements for rolled edges must comply with GOST 14637.

4.1.5 Stratification in rental is not allowed.

4.1.6 In the macrostructure of rolled products, there should not be delaminations, accumulations of rolled bubbles, slag inclusions and flocs visible without the use of magnifying devices.

4.1.7 The hardness of rolled products with a thickness of up to 80 mm inclusive without heat treatment or after controlled rolling must comply with the standards specified in table 2.

Table 2 - Hardness of rolled products

End of table 2

Notes

1 Hardness standards for normalized rolled products were not rejected until 01.01.98.

2 The “+” sign means that the hardness control is carried out for the data set and the control results are recorded in the quality document.

4.2 Characteristics to be set by the user

4.2.1 Rolled plate with increased accuracy in thickness, flatness - improved, high and extra high according to GOST 19903.

4.2.2 Rolled broadband universal, cut-to-length or multiple cut-to-length, improved flatness, with rib curvature class A according to GOST 82.

4.2.3 Rolled plate with a thickness of up to 80 mm inclusive with a cut edge.

4.2.4 Rolled products with a mass fraction of sulfur 0.020% - 0.035%.

4.2.5 Rolled products with a mass fraction of sulfur and phosphorus, reduced against the standards of GOST 1050, GOST 4543, GOST 9045 and GOST 14959.

4.2.6 Rolled products with a thickness of up to 80 mm inclusive in a heat-treated state (normalized, annealed, high-tempered).

4.2.7 Rolled products with a thickness of up to 80 mm inclusive in a heat-treated state with the requirements for hardness given in table 2.

4.2.8 Rolled products up to 80 mm thick from steel grades 08kp, 08ps, 08, 10kp, 10ps, 10, 15kp, 15ps, 15.20kp, 20ps and 20 without heat treatment and continuous rolling mills with hardness in accordance with the standards of table 2 for annealed or high tempered rolled products.

4.2.9 Rolled products with a thickness of up to 80 mm inclusive with mechanical properties in accordance with the requirements given in table 3.

Table 3 - Mechanical properties of rolled products

End of table 3

Notes

1 For steel grade 08Yu, the norms apply only to plate rolled products.

2 With a thickness of rolled products over 20 mm, a decrease in relative elongation by 0.25% abs. for each millimeter of increase in the thickness of rolled products is allowed, but not more than 2% for rolled products with a thickness of up to 32 mm inclusive and by 3% for rolled products with a thickness of more than 32 mm.

3 For annealed rolled steel grades 35, 40, 45 and 50, a reduction in tensile strength by 39 N/mm 2 (4 kgf/mm 2) is allowed.

4 "+" sign means that the characteristic is controlled for the data set. The control results are recorded in the quality document.

4.2.12 Rolled products with a thickness of up to 60 mm inclusive with a 180 ° cold bending test with a mandrel thickness indicated in Table 4. There should be no break, delaminations and cracks visible to the naked eye at the bending point.

Table 4 - Cold bend test

4.3 Characteristics and standards established by agreement between the consumer and the manufacturer

4.3.1 Rolled products with clarification of the requirements for the assortment in relation to GOST 19903 and GOST 82.

4.3.2 Rolled plates with a length of 1.5 to 5 m.

4.3.3 Rolled plate with a thickness of more than 80 mm with a cut edge.

4.3.4 Rolled products with normalized total mass fraction of sulfur and phosphorate.

4.3.5 Rolled products with a reduced mass fraction of residual elements in steel relative to GOST 1050, GOST 4543, GOST 9045 and GOST 14959.

4.3.6 Rolled products with an increased mass fraction of residual elements (chromium, nickel, copper) of steel smelted by scrap or scrap ore processes, in relation to the standards of GOST 1050, GOST 4543, GOST 9045 and GOST 14959.

4.3.7 Rolled steel with a mass fraction of carbon in the brand according to the lower limit of at least 0.3% with a guarantee of a decarburization depth (ferrite + transition zone) of no more than 2% per side of the actual sheet thickness.

4.3.8 Rolled products with a thickness of St. 80 mm in heat treated condition.

4.3.9 Rolled products with a thickness of St. 80 mm with hardness control.

4.3.10 Rolled products with mechanical properties in the normalized state in accordance with the standards specified in table 5.

Table 5 - Mechanical properties of rolled products in a normalized state

End of table 5

Note - The norms of mechanical properties were not rejected until 01.01.98. The control results are recorded in the quality document.

4.3.11 Rolled products with mechanical properties after quenching and tempering in accordance with the standards specified in table 6.

4.3.12 Rolled products from calm steel grades with impact strength control at minus 20 °С, minus 40 °С or minus 50 °С.

4.3.13 Rolled products with ultrasonic continuity testing.

Continuity standards - in accordance with classes 1, 2, 3 according to GOST 22727.

4.3.14 Rolled products with a thickness of more than 10 mm with a macrostructure normalized in points.

4.3.15 Rolled products cleaned from scale. The method of descaling is chosen by the manufacturer.

4.3.16 Rolled products with guarantee of weldability. Weldability is ensured by manufacturing technology and chemical composition.

4.3.17 With deburring.

4.3.18 With sheet-by-sheet testing of the mechanical properties of rolled steel grade 20.

4.3.19 Rolled products by chemical composition.

4.4 Marking of rolled products - according to GOST 7566.

4.4.1 Transport marking - according to GOST 14192.

4.5 Packing, formation of packs and bundles of rolled products - in accordance with GOST 7566.

4.5.1 Packaging of rolled products for the regions of the Far North and equivalent regions - in accordance with GOST 15846.

4.5.2 Rolled products cleaned from scale by pickling shall be lubricated on both sides with neutral oil or neutral oil with an inhibitor addition.

5 Acceptance rules

5.1 General rules for acceptance of rolled products - according to GOST 7566.

5.2 Rolled products are presented for acceptance in batches.

In batches from continuous casting plants, the difference in the mass fraction of carbon in steel should not exceed 0.04%, and in the mass fraction of manganese - 0.15%.

The mass of a batch poured on a continuous casting plant must not exceed 400 g.

It is allowed to form a batch of rolled products of the basic design from steel of several heats.

5.3 Each batch is accompanied by a quality document in accordance with GOST 7566.

In accordance with the order, the quality document has two types of filling:

indicating: "The products comply with GOST 1577";
indicating the results of all types of tests carried out.

Note - If there is no type of quality document in the order, the document is drawn up at the discretion of the manufacturer.

Table 6 - Mechanical properties of rolled products after quenching and tempering

Notes

1 The results of the control of mechanical properties are optional until 01.01.98.

2 The standards of mechanical properties for rolled steel grade 30 are given for thicknesses up to 63 mm.

3 The sign "+" means that the characteristic is determined for the data set. The results are recorded in the quality document.

5.4 Rolled products are subjected to acceptance tests.

5.5 To check the quality of the batch of rolled products are selected:

1) for chemical analysis - samples according to GOST 7565.

The manufacturer carries out control of the chemical composition on the ladle sample, if necessary - in the finished product;

2) for surface quality control - all sheets, rolls and strips;

3) for dimensional control - two sheets, rolls or strips, for sheet-by-sheet rolling - all-sheets, rolls or strips;

4) to control the form - two sheets, rolls or strips;

5) to control hardness and mechanical properties, macrostructure, cold bending tests - one sheet, roll or one strip.

From rolled products made on continuous rolling mills and not requiring heat treatment, samples are taken from the outer coil of the coil.

5.6 It is allowed for a batch of rolled products to apply the results of tests of sheets, coils and strips of steel of the same melting for macrostructure and mechanical properties obtained on batches of rolled products of large thicknesses, to apply to batches of rolled products of smaller thicknesses.

5.7 Upon receipt of unsatisfactory test results for at least one of the indicators, repeated tests are carried out in accordance with GOST 7566.

6 Test methods

For steel from continuous casting plants, the difference in mass fraction of carbon and manganese in the batch is determined by ladle analysis.

6.2 Geometric dimensions and flatness are determined using measuring instruments according to GOST 26877, GOST 162, GOST 166, GOST 427, GOST 7502 or tools certified according to GOST 8.001 or GOST 8.326.

The thickness of rolled products is measured at a distance of at least 100 mm from the ends and 40 mm from the edges.

6.3 Sampling for mechanical tests according to table 3 and technological tests is carried out in accordance with GOST 7564.

Sampling for mechanical tests according to tables 5 and 6 is carried out in accordance with Appendix 2.

6.4 The quality of the rolled surface is controlled visually. Rolled products for the absence of delaminations are controlled by inspection of the edges and ends without the use of magnifying devices. It is allowed to use devices of the IGT-10NK type or other devices of a similar class. When delamination is visually detected, the quality of rolled products is additionally checked by removing chips. At the same time, chip bifurcation is a sign of metal discontinuity.

It is allowed for the consumer to control the absence of delamination after cutting.

6.5 From each sheet, roll or strip selected for inspection:

for tensile and bending tests - one sample each;

for impact bending tests - two samples from rolled products with a thickness of 5 mm or more;

to check the macrostructure - one transverse template 250 mm long from the middle part of the rolled product width;

to test the hardness - two samples each: one from the edge, the other from the middle part of the width of the rolled product;

to control the depth of the decarburized layer - one sample from the edge of the width of the rolled product.

6.6 Tensile test is carried out according to GOST 1497.

Specimens for testing the mechanical properties of broadband products (see Table 3), supplied without heat treatment, are made from normalized billets 25 mm thick. With a strip thickness of less than 25 mm, normalization is carried out on blanks equal to the strip thickness.

6.7 Tensile and impact test specimens (see tables 5 and 6) are cut from heat-treated blanks in the size specified by the consumer.

6.8 Bending test is carried out in accordance with GOST 14019.

6.10 The impact test is carried out according to GOST 9454 on specimens of types 1, 2, 3 and 11.

The mode of heat treatment of workpieces (samples) to determine the impact strength at

temperature of minus 20 °С, minus 40 °С or minus 50 °С rolled products from calm steel grades are set by agreement between the manufacturer and the consumer.

6.11 Hardness determination is carried out according to GOST 9012.

6.12 The macrostructure control is carried out by the etching method according to GOST 10243. The manufacturer can guarantee the requirements for the macrostructure without control.

The methodology and scales for monitoring the macrostructure of rolled products in thicknesses of more than 10 mm are established by agreement between the manufacturer and the consumer.

6.13 Determination of the depth of the decarburized layer is carried out according to GOST 1763.

6.14 Ultrasonic testing is carried out according to GOST 22727.

In technically justified cases, at the request of the consumer, mechanical properties are controlled in accordance with GOST 1497 and GOST 9454.

7 Transport and storage

7.1 Transportation and storage - according to GOST 7566.

7.2 Rolled products are transported by transport of all types in accordance with the rules for the carriage of goods in force for this type of transport.

7.3 When transporting rolled products by rail, the type of shipment is carload.

Loading, fastening and placement of rolled products must be carried out in accordance with specifications loading and securing cargo, approved by the Ministry of Railways and GOST 22235.

APPENDIX 1 (mandatory)

Rental designation scheme

AT design documentation it is allowed to give examples of symbols in accordance with the diagram shown in Figure 2. The amount of information indicated in the design documentation can be reduced.

Legend Examples

Rolled plate, normal accuracy in thickness (B), normal flatness (PN), with a cut edge (O), dimensions 6x700x6000 mm according to GOST 19903-74, from steel grade 20, with hardness according to (TV1), mechanical properties according to table 3 (M1), with a bend test in a cold state (CI), in a thermally treated state (TO), with filling out a document on the quality of the type DK1:

Sheet B-PN-O-6 x 700 x 6000 GOST 19903-74/20-TV1-M1-KI-TO-DK1 GOST 1577-93 Rolled plate, normal accuracy in thickness (B), normal flatness (PN), unedged edge (HO), dimensions 6 x 700 x 6000 mm according to GOST 19903-74, from steel grade 08, with hardness according to table 2 for annealed or high-tempered rolled products (TV2), with mechanical properties according to table 3 for annealed or high-tempered rolled products (M2), without heat treatment, with filling in the quality document type DK1:

Sheet B-PN-NO-6 x 700 x 6000 GOST 19903-74/08-TV2-M2-DK1 GOST 1577-93 Rolled broadband, random length (ND), improved flatness (PU), with rib curvature class A, s unedged edge (HO), dimensions 6 x 700 x 6000 mm according to GOST 82-70, made of steel grade 35, with hardness according to table 2 (TV1), with mechanical properties according to table 5 (M3), with a guarantee of decarburization no more than 2% on the side (1С), with ultrasonic continuity testing of class 2 (2UT), without heat treatment, with filling out a document on the quality of type DK2:

Strip ND-PU-A-NO-6 x 700 x 6000 GOST 82-70/35-TV1-M3-1S-2UZK-DK2 GOST 1577-93 Examples of symbols allowed in design documentation:

Rolled plate, normal accuracy in thickness (B), normal flatness (PN), with a cut edge (O), dimensions 6 x 700 x 6000 mm according to GOST 19903-74, from steel grade 20, with hardness according to table 2 (TV1), mechanical properties according to table 3 (M1), with a bending test in a cold state (KI), in a heat-treated state (HT):

Rolled broadband, random length (ND), improved plane (PU), with rib curvature of class A, with an unedged edge (NO), dimensions 6 x 700 x 6000 mm according to GOST 82-70, made of steel grade 35, hardness according to table 2 (TV1), with mechanical properties according to table 5 (M3) with a guarantee of decarburization no more than 2% per side (1C), with ultrasonic continuity control class 2 (2UT), without heat treatment:

(Amendments).

APPENDIX 2 (mandatory)

Sampling scheme for the control of mechanical properties given in tables 5 and 6 of this standard

Table 1

* For rolled products with a thickness of 5-10 mm, the width of the sample is equal to the thickness of the rolled products, the height is 10 mm.

For rolled products with a thickness of more than 30 mm, the sample, by agreement between the manufacturer and the consumer, is cut out at a distance of 1/4 of the thickness of the rolled products.

APPENDIX 3 (reference)

Modes of heat treatment of workpieces to control the mechanical properties given in tables 5 and 6 of this standard

Rolled sheet and broadband universal from structural steel (GOST 1577-93)

SHEETS AND BROADBAND UNIVERSAL STEEL
STRUCTURAL QUALITY (GOST 1577-93)

GOST 1577-893 applies to hot-rolled sheet metal with a thickness of 4 to 160 m and hot-rolled broadband universal steel with a thickness of 6 to 60 mm from high-quality carbon and alloy steel.
Depending on the type of metal products and the thickness of sheets and strips, rolled products are manufactured in accordance with GOST 1577-93 from steels of the following grades:

Rolled sheet	4 - 160	08kp, 08ps, 08, 10kp, 10ps, 10, 15ps, 15kp, 15, 20kp, 20ps, 20, 25, 30, 35, 40, 45 (carbon quality structural steel)
Rolled sheet	4 - 80	50, 55, 60 (carbon quality structural steel); 65.70, 60G, 65G, 70G (spring-spring carbon and alloy steel); 15G, 20G, 3OG, 40G, 50G, 10G2, 35G2, 20H, ZOH, 38HA, 40H, 45H (structural alloy steel)
Universal broadband rental	6 - 60	08kp, 08ps, 08, 10kp, 10ps, 10, 15ps, 15kp, 15, 20kp, 20ps, 20, 25, 30, 35, 40, 45 (carbon quality structural steel) 20X, 3OX, 40X (structural alloy steel)

The chemical composition of high-quality carbon structural steel must comply with the standards of GOST 1050-88, alloyed structural steel - GOST 4543-71, spring-spring carbon and alloy steel - GOST 14959.
Depending on the standardized characteristics, rolled products are produced in three categories:
1 - by chemical composition;
2 - by chemical composition and hardness;
3 - in terms of chemical composition, mechanical properties and hardness - for sheets up to 80 mm thick and strips.
The category is specified in the order; in the absence of instructions, the category is set by the manufacturer.
Rolled sheets up to 80 mm thick and broadband products are produced by:
- without heat treatment;
- heat-treated - T (annealed, normalized, high tempered).
In terms of shape, dimensions and maximum deviations, rolled products must meet the requirements of:
GOST 19903-74 - for hot-rolled sheet;
GOST 82-70 - for universal hot-rolled broadband steel (with rib curvature of the usual manufacturing accuracy - class B).
Symbol example: hot-rolled sheet with dimensions 6x700x6000 mm, normal rolling accuracy (B), normal flatness (PN) according to GOST 19903-74, from steel grade 20, category 2, thermally wrapped (T):


Designation	GOST 1577-93
Title in Russian	Thick-plate and wide-strip rolled products made of high-quality structural steel. Specifications
Title in English	Rolled sheets and wide strips of structural quality steel. Specifications
Date of entry into force	01.01.1997
OKS	77.140.20
OKP code	098100
KGS code	B33
OKSTU code	0981
SRSTI rubricator index	534335
Annotation (scope)	This standard applies to hot-rolled thick-plate and broad-strip products made of high-quality structural unalloyed and alloyed steel.
Keywords	rental; mechanical properties ; surface quality ; acceptance rules; test methods;
Type of standard	Standards for products (services)
Designation of the replacement(s)	GOST 1577-81
Note	OKS code has been corrected in accordance with the 2007 standards index.
Normative references to: GOST	GOST 8.001-80; GOST 8.326-89; GOST 82-70; GOST 103-76; GOST 535-88; GOST 1497-84; GOST 4543-71; GOST 7502-98; GOST 7564-97; GOST 7565-81; GOST 7566-94; GOST 9012-59; GOST 9045-93; GOST 9454-78; GOST 10243-75; GOST 12344-88; GOST 12345-2001; GOST 12346-78; GOST 12347-77; GOST 12348-78; GOST 12350-78; GOST 12351-81; GOST 12352-81; GOST 12354-81; GOST 12357-84; GOST 12360-82; GOST 14019-80; GOST 14192-96; GOST 14637-89; GOST 14959-79; GOST 15846-79; GOST 19903-74; GOST 22235-76; GOST 22536.0-87; GOST 22536.1-88; GOST 22536.2-87; GOST 22536.3-88; GOST 22536.4-88; GOST 22536.5-87; GOST 22536.6-88; GOST 22536.7-88; GOST 22536.8-87; GOST 22536.9-88; GOST 22536.10-88; GOST 22727-88; GOST 26877-91; GOST 28473-90
Regulatory references to: Other	PR 50.2.009-94
The document was submitted by the CIS organization	Gosstandart of the Russian Federation
The document was adopted by the CIS organization	Interstate Council for Standardization of Metrology and Certification
Protocol number	2
Acceptance date	15.04.1994
Associated countries	Republic of Armenia; Republic of Belarus; The Republic of Kazakhstan; Republic of Kyrgyzstan; The Republic of Moldova; The Russian Federation; Turkmenistan; Ukraine
Department of Rostekhregulirovanie	320 - Management of standardization and certification of raw materials and materials
Russian Technical Committee	120 - Cast iron, steel, rolled
MND developer	the Russian Federation
Date of last edition	01.01.2002
Number(s) of change(s)	revised edition
Number of pages (original)	18
Organization - Developer	Center for Standardization and Certification of Metal Products
Status	Active

GOST 1577-93

INTERSTATE STANDARD

RENTAL PLATE AND BROADBAND
FROM STRUCTURAL QUALITY STEEL

TECHNICAL CONDITIONS

INTERSTATE COUNCIL
ON STANDARDIZATION, METROLOGY AND CERTIFICATION

Minsk

Foreword

1 DEVELOPED by the Center for Standardization and Certification of Metal Products, Technical Committee for Standardization TC 120 "Iron, Steel, Rolled Products"

INTRODUCED by the State Standard of the Russian Federation

2 ADOPTED by the Interstate Council for Standardization, Metrology and Certification on April 15, 1994 (Report of the Technical Secretariat No. 2)

State name	Name of the national standardization body
Republic of Armenia	Armstate standard
Republic of Belarus	State Standard of the Republic of Belarus
The Republic of Kazakhstan	State Standard of the Republic of Kazakhstan
Republic of Kyrgyzstan	Kyrgyzstandart
The Republic of Moldova	Moldovastandard
the Russian Federation	Gosstandart of Russia
Turkmenistan	Main State Service "Turkmenstandartlary"
	State Standard of Ukraine

3 By the Decree of the Committee of the Russian Federation for Standardization, Metrology and Certification dated March 19, 1996 No. 180, the interstate standard GOST 1577-93 was put into effect directly as the state standard of the Russian Federation from January 1, 1997.

4 INSTEAD OF GOST 1577-81

5 EDITION (January 2002) as amended (IUS 4-99, 1-2000)

GOST 1577-93

INTERSTATE STANDARD

PLATE AND BROADBAND RENTAL
FROM STRUCTURAL QUALITY STEEL

Technical conditions

Rolled sheets and wide strips of structural quality steel.

the date introductions 1997-01-01

1 Scope

This standard applies to hot-rolled thick-plate and wide-strip products made of high-quality structural unalloyed and alloyed steel.

2 Normative references

GOST 8.001-80* State system for ensuring the uniformity of measurements. Organization and procedure for conducting state testing of measuring instruments

GOST 8.326-89* State system for ensuring the uniformity of measurements. Metrological certification of measuring instruments

* PR 50.2.009-94 is in force on the territory of the Russian Federation.

GOST 82-70 Universal hot-rolled broadband steel. Assortment

GOST 103-76 Hot-rolled steel strip. Assortment

GOST 535-88 Rolled bars and shapes from carbon steel of ordinary quality. General specifications

GOST 1497-84 (ISO 6892-84) Metals. Tensile test methods

GOST 4543-71 Rolled products from alloyed structural steel. Specifications

GOST 7502-98 Metal measuring tapes. Specifications

GOST 7564-97 Rolled products. General rules for sampling, blanks and samples for mechanical and technological tests