If the rear view camera does not work in your car, this is not a reason to despair. In most cases, the problem lies in small malfunctions that you can fix yourself. You will learn about what to do if the car does not work and how to fix it from the article.

[ Hide ]

Typical malfunctions of the rear view camera

Most often, this device is located in the car in three places. This is either a trunk lock (handle), or a frame for a license plate light, or it can be installed in the cabin (in station wagons).

As practice shows, cameras that are decided to be installed directly in the cabin suffer the least from any problems. After all, they are not exposed to aggressive influences. environment. This impact primarily refers to moisture entering the device.

The ingress of water into the device can lead not only to its complete failure to work. Image defects may occur. Often, car owners complain that the camera does not show an image or the picture looks cloudy. Most likely, the reason for this is precisely the ingress of moisture into the rear view camera.

Troubleshooting and Removing the Device

Each car owner has two ways to repair the rear view camera. The first of them and the simplest is to send it in for repair. You can contact your manufacturer's service center. If the machine is still under warranty, then this must be done. Self repair will void your warranty.

But often it will be cheaper and easier to carry out a simple repair yourself. If the rear view camera has stopped working or there are malfunctions, you can try to repair it.

The instruction will be given on the example of KIA cars.

1. If the rear view camera does not turn on automatically or at all, in order to remove it, you need to dismantle the entire trim.
2. To do this, first remove a small panel in the upper part, under which the bolts are hidden. Remove them to remove the main body of the skin.
3. Under it you will find four nuts that secure the trunk handle. The camera itself is fixed with two self-tapping screws, two more fix its connector.
4. You may encounter traces of corrosion. First remove it, and then you can disassemble the device.
5. The case is tightened with four self-tapping screws. When you disassemble the device, be careful - they can oxidize.
6. If there is moisture inside the chamber, then it will need to be dried. Brush and then varnish the boards to protect them from moisture.
7. There are usually two gaskets in the chamber. One is placed on the eyepiece of the camera, and the other is located at the junction between the plastic parts of the camera and metal case. Both could become unusable after a certain period of operation. Replace them if necessary.
8. Assemble the camera back; it is necessary to act in the reverse order, having previously treated all joints with sealant. It is better to use butyl rubber.

Instructions for adjusting the device with your own hands

When you installed the camera, it works fine, clouding has disappeared, it is important to adjust it correctly. Not all car owners know how this is done. Because of this, they cannot do everything with their own hands and check the performance of the device.

The main task is to set up parking lines. This enabled mode greatly facilitates parking.

1. Take an ordinary wooden block, 2 meters long. Its sides should be 2-3 centimeters.
2. Put it a meter away from the center of the rear bumper. The edges of the bar should protrude from the sides of the car at approximately the same distance.
3. Then, get into the car and go to the service menu. It may be necessary to perform additional actions, for example, turning the parking lights on and off several times.
4. After that, you will need to get into the camera settings and select the brand of the car.
5. When the rear view camera is activated, you will need to turn the steering wheel first to the right until it stops, and then to the left - this is done to adjust it. Then click next. A rectangle will appear on the screen.
6. Using the up, right, down and left keys, you will need to place it so that the bar is exactly in the center. Then click on confirmation.

This, in fact, is all the steps that you need to perform to configure devices. Now, when you turn it on, yellow lines will begin to appear to make parking easier. Please note that any subsequent disassembly may require subsequent reconfiguration of the device.

Issue price

Video "Repair and replacement of the rear view camera"

This video shows the disassembly and repair of the device using the example of a standard Kia Sorento camera (author - PCAVTO).

I ordered an original camera from China for over 3 thousand rubles.
I installed it myself within a few days.

Replacing the handle with a pen camera is not difficult.

First you need to unscrew the two screws in the handle.

Then we pull off the plastic cover, it is on clips

Then we unscrew the trunk handle in the sequence as in the photo 1 - remove the handle connector, very carefully the plastic is fragile (I broke it) 2 - unscrew the head to 103 - squeeze the latch with pliers.

We install the purchased camera.

Now check the operation of the camera (without filter).

1. Connect the video cable to the radio
2. The other end of the video cable to the camera. Now you need to connect the power of the camera. For testing, it was powered from the taillight connector.

We turn on the ignition, put in reverse, wait for the picture and nothing happens. We take 12v from other places, even from the battery. Damn. And then it dawned on me, it is necessary to register in the brain (block37, byte3, tick bit6). And then AnKor868 responded to my call, for which a huge THANK YOU to him.

We connect and voila everything works.

Below is a photo of the image and the distance to the objects

Next Post Installing the Rear View Camera (Part 2 - Laying the Cable)

Issue price: $125 Mileage: 20125 km

www.drive2.ru

Thread: Need help checking rear view camera.

1. Gastello, ahead of the non-simultaneous connection)))
2. Message from Gastello Connect the red wire to the positive from the ignition or to the wire where there is power in the ACC key position, the black one is naturally negative (ground), and the green one to the reverse light, or find the wire under the threshold on which + appears when reverse gear is engaged. Well, as mentioned above, the camera is also negative and positive when reverse gear is engaged, you can directly on the lamp. And, accordingly, the video signal with a cable with tulips from the camera to the monitor input. Everything will work if not defective. To check, first connect the red and black wires, and then put green on red. Not immediately, but there in a minute. How do you check at home?
3. there is also a power supply. Power the monitor from it (black and red wires). Power the camera from it, connect the camera to the monitor with a video cable with tulips, and after all this, put the green wire on the red ones, that is, on the plus. The monitor will start and show the image from the camera
4. Message from Gastello Yes, as for a phone, only at the output 12v, 1 ampere.
5. Message from Instalytor And what kind of accompanying papers (instructions, diagrams) were included?
6. I have a power supply unit of one ampere GU pulls, I think that's enough. If there is a tester, connect it too to check the voltage, if not, then do not connect the camera and the current monitor as described above, one monitor unit will definitely pull, the current instead of the image will be a black square with the inscription that there is no signal. If the power supply pulls the camera, then plant a tulip on AV2
7. Everything and the camera and the monitor work. Not so connected the cable from the monitor, this was the whole problem, it was stuck and everything works. Thanks everyone.

   Sorry for the extra noise

Kiario4.ru

Do-it-yourself car rear-view camera repair and adjustment

If the rear view camera does not work in your car, this is not a reason to despair. In most cases, the problem lies in small malfunctions that you can fix yourself. You will learn about what to do if the rear view camera does not work in the car and how to fix it from the article.

Most often, this device is located in the car in three places. This is either a trunk lock (handle), or a frame for a license plate light, or it can be installed in the cabin (in station wagons).

As practice shows, cameras that are decided to be installed directly in the cabin suffer the least from any problems. After all, they are not exposed to aggressive environmental influences. This impact primarily refers to moisture entering the device.

The ingress of water into the device can lead not only to its complete failure to work. Image defects may occur. Often, car owners complain that the camera does not show an image or the picture looks cloudy. Most likely, the reason for this is precisely the ingress of moisture into the rear view camera.

Troubleshooting and Removing the Device

Each car owner has two ways to repair the rear view camera. The first of them and the simplest is to send it in for repair. You can contact your manufacturer's service center. If the machine is still under warranty, then this must be done. Self-repair will void your warranty.

But often it will be cheaper and easier to carry out a simple repair yourself. If the rear view camera has stopped working or there are malfunctions, you can try to repair it.

The instruction will be given on the example of KIA cars.

1. If the rear view camera does not turn on automatically or at all, in order to remove it, you need to dismantle the entire trim.
2. To do this, first remove a small panel in the upper part, under which the bolts are hidden. Remove them to remove the main body of the skin.
3. Under it you will find four nuts that secure the trunk handle. The camera itself is fixed with two self-tapping screws, two more fix its connector.
4. You may encounter traces of corrosion. First remove it, and then you can disassemble the device.
5. The case is tightened with four self-tapping screws. When you disassemble the device, be careful - they can oxidize.
6. If there is moisture inside the chamber, then it will need to be dried. Brush and then varnish the boards to protect them from moisture.
7. There are usually two gaskets in the chamber. One is placed on the eyepiece of the camera, and the other is located at the junction between the plastic parts of the camera and the metal case. Both could become unusable after a certain period of operation. Replace them if necessary.
8. Assemble the camera back; it is necessary to act in the reverse order, having previously treated all joints with sealant. It is better to use butyl rubber.

Instructions for adjusting the device with your own hands

When you installed the camera, it works fine, clouding has disappeared, it is important to adjust it correctly. Not all car owners know how this is done. Because of this, they cannot do everything with their own hands and check the performance of the device.

The main task is to set up parking lines. This enabled mode greatly facilitates parking.

1. Take an ordinary wooden block, 2 meters long. Its sides should be 2-3 centimeters.
2. Put it a meter away from the center of the rear bumper. The edges of the bar should protrude from the sides of the car at approximately the same distance.
3. Then, get into the car and go to the service menu. It may be necessary to perform additional actions, for example, turning the parking lights on and off several times.
4. After that, you will need to get into the camera settings and select the brand of the car.
5. When the rear view camera is activated, you will need to turn the steering wheel first to the right until it stops, and then to the left - this is done to adjust it. Then click next. A rectangle will appear on the screen.
6. Using the up, right, down and left keys, you will need to place it so that the bar is exactly in the center. Then click on confirmation.

This, in fact, is all the steps that you need to perform to configure devices. Now, when you turn it on, yellow lines will begin to appear to make parking easier. Please note that any subsequent disassembly may require subsequent reconfiguration of the device.

Issue price

Video "Repair and replacement of the rear view camera"

This video shows the disassembly and repair of the device using the example of a standard Kia Sorento camera (author - PCAVTO).

How to connect a rear view camera

Not all hybrid vehicles come with a parking camera. And on such cars, it will not be superfluous at all, especially during parking.

The natural desire of the owners of such cars is the desire to correct this shortcoming. Connecting a rear view camera is a process that almost any car owner can handle.

What may be required if you decide to install the camera yourself? You will need the following items: a parking camera that you purchased in advance; small terminals or ready-made wires with terminals; special clips for wires; screwdriver (knife); pliers; washer hose; tee for washer hose; multimeter (tester); drill.

Most often, the parking camera is installed in the standard hole of the "native" head unit. Therefore, before buying a camera, make sure you have it. So, your car has a connector for parking cameras, you went to the store where you purchased the best camera option for you.

Where to start? And it’s worth starting with the fact that, without being too lazy, check all the wires used with a tester. You will not burn anything with a voltmeter, but with a light bulb - easily.

Before disassembling the half-machine, carefully inspect the camera itself. Checking the performance of each camera may vary slightly. Therefore, for this it is best to use the widely available step by step instructions to check the camera of a particular brand. Connect the rear view camera only after making sure that the camera itself is working. The following is rough plan actions.

Rear view camera: connection

It is necessary to remove the trim from the rear door, as well as the rear frame with headlights. Bolts are unscrewed in order to remove the cable from the door handle.

Try on the camera, then drill a hole for it.

If desired, you can immediately install washer nozzles on the camera. If you decide to install them, then also drill a hole under them, as well as a hole in the door to stretch the hose and wires.

After that, return the frame to its place, but do not rush to screw it on, first make sure that the camera is installed in the direction you need.

And then directly connect the rear view camera itself. Power for the camera is taken from the rear light. Put on a tee instead of the tailgate washer hose. Check for leaks several times and fix them.

How to check if the rear camera, video surveillance is working and how to check the camera on a computer, laptop - read the answers of experts.

Answer:

The webcam is connected to the computer via a USB cable or may be built-in. Before checking if the camera is working, you must first find out if the cable is inserted all the way and whether it matches this port?

After confirming the physical connection, you need to check if the webcam is installed correctly. Here you need to select the path: "Control Panel", "System", "Hardware", "Device Manager". Next on the list is the webcam. If the icon has a yellow exclamation point, the device drivers are not working and should be updated. There are several ways to do this:

• right-click on the webcam icon and select "Update driver";
• use the disc supplied with the webcam;
• use the DriverFinder program from the Internet.

How to check if the camera is working on a computer? You can use online services such as Test Webcam. To do this, you need to go to the site, after which access to the webcam is made. This test checks the image feed and evaluates its quality.

Drivers are also checked and installed on the laptop. The camera is physically connected correctly by default. The laptop keyboard may have hot key, which you can use to check your webcam.

How to find out if the security camera or rear view camera is working

Video surveillance serves to protect objects. The customer considers that the installation is the most important and no further maintenance is required. But over time, the system may break down. How to find out if the CCTV camera is working and what are the malfunctions in it? You can do this by tracking down the following failures:

• the monitor disappears. In this case, the power supply to it and the health of the monitor itself are checked;
• failure of one of the cameras. All connectors should be checked. During any checks, it is always necessary to determine the presence of voltage in the network. It may be absent due to a cable break or damage to the connection contacts;
• streaks or flickering appear on the screen. The cause may be an insulation failure or a bad connection;
• The DVR does not work due to damage or a malfunction of the power supply. If these malfunctions are eliminated and the device does not work, it should be taken for repair.

Unlike security devices, the car's rear view video recorder works for a short time, mostly for parking the car or for shooting and recording traffic incidents. To connect it, you need a radio tape recorder with a monitor (multimedia center). They contain a connector for connecting the video camera cable. Some models of video cameras are made together with monitors. In these cases, you can do without a multimedia device.

The system is turned on by a toggle switch on the driver's instrument panel. All cameras must be powered and the video signal can be wired or wireless. When purchasing a wireless module, you should check whether it can work with this car radio.

The camera is inserted into the hole in the bumper or body, but is firmly fixed only after the appearance of a clear picture on the monitor, without the presence of elements of the car body on it. It is advisable to mount the camera higher from the road to reduce pollution.