Unimat series 200

Specially designed for companies that work on a tight budget but don't want to sacrifice quality. An impressive list of standard equipment and options. Can also be used as a second machine for small series. Available in 5 and 6 spindle configurations.

New Unimat 200 series: precise, adaptable to various planing and profiling conditions:

• Impeccable processing quality
• Impressive power reserve
• Easy and fast setup
• Simplicity and convenience in operation
• Maximum work safety
• The accuracy of the execution of the machine components themselves and the resulting products
• Heavy cast bed components help dampen vibrations, resulting in highest quality treated surfaces

Technical data:

Model / Key Features
Number of spindles	5 spindles	6 spindles
Working width	20 -230 mm	20 -230 mm
working height	8 -120 mm	8 -120 mm
Engine power: IE2 motors and EMGS technology
1st lower horizontal spindle	5.5 kW	7.5 kW
1st right vertical spindle	11 kW	5.5 kW
1st left vertical spindle	together with the right	7.5 kW
1st upper horizontal spindle	7.5 kW	7.5 kW
2nd top horizontal spindle	-	7.5 kW
2nd lower horizontal spindle	7.5 kW	7.5 kW
Spindles: All molding spindles are dynamically balanced for high running accuracy
Spindle diameter	40 mm	40 mm
Spindle speed	6000 rpm	6000 rpm
Feed system:
Feed rate (frequency adjustable)	5 - 30 m/min	5 - 30 m/min
Feed motor power	4 kW	4 kW
Number of feed rollers on top	5	6
Number of driven rollers in the table	1	2
Feed roller in front of the first lower tool, pneumatically adjustable in height and depth	standard	standard
Self-cleaning needle rollers with depth gauge	standard	standard
Planer table length (incl. guide fence)	2 m	2 m
Rebate tool including grooving cutter	standard	standard
Max. horizontal tool diameter (except for the 1st lower one)	200 mm	200 mm
Max. vertical tool diameter	200 mm	200 mm
Chrome plated working surface table and stops (except for the entrance table and special plates)	standard	standard
Hand pump for supplying waxilite lubricant for deresining tables	standard	standard
Centralized lubrication points on the front of the machine	standard	standard
CE version	standard	standard
Cutting tool included	4 planer heads	4 planer heads

Possible additional options:

• Memory control system - to store the values ​​of the spindle positions for the production of certain profiles
• increase in engine power on horizontal spindles up to 11 kW
• increase in engine power on vertical spindles up to 11 kW
• shortened distance between the rollers opposite the right spindle
• spindle quick nut
• planer table length (incl. guide fence) 2.5 m

Machine Unimat Super 4

The patented longitudinal milling technology allows 4-sided machining even on 3-spindle machines with a feed speed of 24 m/min and obtain ideal surfaces for gluing. The machine is equipped with a combined tool on the upper spindle, which provides the necessary perpendicularity and parallelism of the surfaces, and due to the grooved guides, the unit copes with both oblique and short workpieces. The Unimat Super 4 is compact and ideal for integration into production lines.

Longitudinal milling Unimat Super 4 allows four-sided machining even on three-spindle machines, at a feed rate of 24 m/min. and obtain surfaces suitable for gluing. The combination tool on the top spindle ensures the necessary parallelism and squareness of the surfaces. With the help of grooved guides, the machine processes short workpieces, as well as workpieces with oblique cuts. Unimat Super 4 is well suited for the production of laths for glued boards.

The Unimat Super 4 is compact and requires little space. It is advisable to place the Unimat Super 4 longitudinal milling machine in front of the size press.

Specifications Unimat Super 4

Working width, (mm): 25 - 150;

Working height, (mm): 15 - 50;

Number of spindles, (pieces): 3;

Speed ​​of rotation of the 1st and 3rd spindles, (rpm): 6000;

Rotational speed of the 2nd spindle, (rpm): 7000;

Feed rate, (m/min): 6 - 24;

Engine power of the 1st lower horizontal spindle, (kW): 11;

Motor power of the 2nd upper horizontal spindle, (kW): 18.5 - 22;

UNIMAT logo

Innovations in the field of electric heating are being introduced everywhere. And along with the ones we wrote about earlier, a brand like Unimat appeared, working on carbon rods, and promising at least 20 years of continuous operation. But, as they say, it was smooth on paper... Let's see if the Unimat warm floor is so reliable and whether it is worth making a choice in its favor.

Operating principle

In we already wrote how a semiconductor can change resistance depending on temperature environment. Unimat underfloor heating uses the same principle, but instead of a cable, parallel carbon rods are used, connected to a “ladder” with an appropriate cable.

Unimat in turn

Thus, it turns out that the colder parts of the room (for example, near the entrance or window) consume more electricity, while the warmer ones, on the contrary, consume a minimum or do not heat up at all. The economic effect of such a reasonable use is very large and can significantly save on electric heating.

Positive aspects of Unimat

1. Ease of installation. Floors are mounted in a screed or directly under the tiles without any problems - just read the instructions
2. High level of efficiency - provided by self-regulation of carbon rods
3. The ability to flexibly configure on / off modes (although this plus applies more to thermostats)
4. The distance between the rods can be changed at will, depending on the geometry of the room
5. Not afraid of overheating - carbon rods that are warm simply will not turn on, so overheating is impossible
6. Even distribution of heat throughout the floor

Disadvantages identified during operation

During the operation of Unimat warm floors, very serious shortcomings were revealed, which managers, sellers and the manufacturer try not to talk about, talking about the super-reliability of their product, about a 20-year warranty, etc.

• After installing the warmest floor, you, of course, check whether it heats up or not by plugging it into the network. But after pouring the screed, you will have to wait at least 28 days before turning it on for the first time. The term is very significant if you made repairs in late summer / early autumn
• It is unrealistic to use Unimat as the main heating in conditions of 30 degrees below zero - the power of the heating elements is too low.
• Contacts with carbon rods. This is the main drawback of the entire system and it is here that the main negative feedback from customers lies.

Here, contact with the carbon rod is usually lost.

The fact is that each rod is connected to a conductive wire using a protruding spike that goes inside the rod itself to a depth of only 3 mm. This is very little for reliable contact.

If you lay (on the manufacturer's advice, by the way) a thermal mat directly under the tile, and at the same time use (again on the manufacturer's advice) a heat-insulating coating 2-3 mm thick, then the tile under your feet will move a little during operation. This may not be noticeable to you, but it is quite enough that poor-quality contact between the carbon rod and the copper shield first becomes unreliable, and then completely disappears.

Many buyers, after "opening" Unimat warm floors, found a lot of burnt contacts.

When it comes to the bathroom, the number of dissatisfied buyers here goes off scale! Moisture that gets on the same contacts simply “kills” the floors in a year or two of use.

20 year guarantee… Even if you can prove that the floors were laid according to the instructions, and even qualified specialist, then in return they will provide you with exactly the same Unimat warm floor, with the words that this one is certainly without factory defects. And there are two troubles:

1. Bad contacts are not a factory defect, this is a design feature of the model, so you will get exactly the same low-quality floor
2. No one will reimburse you for the cost of the screed, tiles and your nerves

What to do?

There are plenty of other offerings on the market, including those from Caleo, the Unimat manufacturer, that are more reliable and simpler in design, without losing the functionality and benefits of this unfortunate model. For example Unimat Cord.

Self-regulating heating cable from other manufacturers can also be used. It will act no worse, but it will last much longer.

Comments:

Similar posts