Each phone connected to the Megafon network wonders how to set up the Internet? Without the correct settings, you will not be able to use the network and MMS. This applies to both conventional phones and massively used smartphones.

When you install a SIM card in any modern mobile device, it is configured automatically. However, sometimes it happens that the settings themselves were not installed or were not registered - then you need to set up the phone manually. This review will tell you how automatic tuning works, as well as how to enter the settings yourself.

Ordering Internet settings from Megafon

Using SMS commands, the user can get Megafon Internet settings for his phone. If you want to set up access, you must send to the number 5049 the number "1", after which an SMS containing the profile settings will be sent. You need to save them and activate the profile, then try to enter the network. On Megafon, GPRS settings are also available in help desk, for this we dial the number 0500, name the model of the phone used and wait for the service SMS with the settings.

By visiting the Megafon website, on it, in the Self-Service Services section, you can find another subsection with Mobile device settings, in which individual settings are ordered that are suitable for any mobile phone model. We select the brand of the phone, model, as well as the ordered data in the drop-down lists, below we enter the phone number used to send the required settings.

Internet settings Megafon manually

APN settings (or access points) on Megaphone can be done manually. To do this, a new profile is created on the phone containing the following data:

• Profile name: specify, for example, Megafon (absolutely any names are allowed here);
• Home page: type megafon.ru (you can also enter any address, since this setting concerns the home page used by the phone's built-in browser);
• Access point: drive in internet;
• Authentication: choose "normal";
• Login with password: do not need to fill.

There may also be settings for a proxy server, but it is recommended to disable the use of a proxy, you do not need to fill in any data here. After filling in the specified settings, by opening a browser, you can try to launch the Internet on your phone.

If you need to figure out how to set up the Internet on Megafon using 3G technology, then there is no need to make additional settings for the third generation network, just go to the item called "Properties of mobile networks" and check that there is a search for a WCDMA network (or the forced registration function is set for WCDMA networks).

When making the above settings, remember that the menu item containing the Internet profile setting may be different depending on the specific smartphone model. In addition, there may also be differences in the names of the fields to be filled in, for example, "Access Point", as well as "APN" - this is a similar name.

Setting up MMS on Megaphone

The procedure for setting up MMS for the Megafon operator is almost identical to ordering for the Internet. To get a working function that allows you to receive and send multimedia MMS messages, you need to send the number "3" to the number 5049. After a short time, the phone will receive a message containing the necessary settings: you need to save them, then apply and try to send MMS to any Megafon number. Similarly, automatic settings are ordered through the Megafon website, after selecting the phone model from the list provided.

Setting up MMS on your phone manually

In cases where you cannot accept automatic settings or install them, you will have to enter the settings manually. To do this, a profile is created on your phone, indicating the data below:

• Profile name: you can just dial MMS (you can enter anything);
• Server or home page address: specify http://mmsc:8002 (no change);
• Proxy: must be "enabled";
• Address for the proxy: we drive in the numbers 10.10.10.10;
• Port field for the proxy used: 8080;
• APN (or may be the name "Access Point"): mms;
• The user and password fields are not required.

As with setting up an Internet profile, depending on the smartphone you are using, some items may have different names.

Setting up the Internet on 3G (4G) Megafon modems

Such popular 3G and 4G modems offered by Megafon are usually sold with settings already made: after purchasing the device, it connects to any USB port, after which you must wait for the installation to finish, which is launched automatically by the modem's control program. After that, everything is prepared for Internet access.

If the data that was present in the automatically created profile was lost, then you can manually configure the Megafon modem. To do this, you need to create a profile and the following is written in it:

• Profile name: specify any, for example, Internet Megafon;
• Access point or APN: internet;
• Number for dialing: dial *99# in the field;
• The username and password fields are not required.

Everything is ready to check if you have an Internet connection.

In order to mobile phone could access the Internet and send/receive MMS messages, it is necessary to register the appropriate settings in it. Without settings, access to the above services will not be possible. In principle, almost all modern phones are configured automatically - activating a new SIM card leads to an automatic ordering of settings that will only have to be applied. After that, just in case, you need to restart the phone so that the settings take effect as correctly as possible.

But sometimes it happens that the phone remains unconfigured. In this case, you need to make manual settings or order automatic settings from the network. In this review, we will analyze all the ways to make settings for accessing the Internet from Tele2. MMS settings will also be considered.

The easiest way to set up your phone is to order automatic Internet settings on Tele2. They will be accepted from the network and registered in the corresponding profiles. You can order Internet settings on Tele2 by calling 679- they will be received within a few minutes in the form of incoming SMS messages. After that, you can access the network using a built-in or downloaded browser from somewhere (for example, Opera Mini, which saves traffic).

How to manually set up the Internet on Tele2

If the Tele2 Internet settings for some reason are not accepted or not installed, manual settings should be registered. You do not need to give your phone into the hands of specialists and, moreover, pay money for it - you can set all the settings yourself, there is nothing complicated about it. To enter the settings, you need to create a network profile and register the following items there:

• Profile name - Tele2 Internet (you can enter anything);
• Home page - http://m.tele2.ru/
• Proxy - off (respectively, we do not enter any settings here);
• Connection type - GPRS;
• Access point (APN) - internet.tele2.ru (without http://);

If necessary, specify the created profile in the browser settings.

Some phones specify a profile for Java applications. If Internet access does not appear, the phone needs to be restarted. With settings Chinese phones you will have to suffer, since the names of the items there can be completely different.

How to set up Internet from Tele2 on Android

If the operating system version is 2.3 or lower, you need to go along the following path: Settings - Wireless - Mobile networks - Internet access points. After that, press Menu and select Create APN. Here we set the following settings:

• Name - TELE2 Internet;
• APN - internet.tele2.ru (without http://);
• MCC - 250;
• MNC - 20;
• APN type - default.

Other items should be left blank. Next, press Menu and Save, after which we try to go online. Don't forget to enable data transfer. Is your smartphone running Android 3.0 or higher? Then the settings will be different. We pass along the following path: Menu - Settings - More - Mobile network - Access points (APN). We call the menu with a button or a virtual button in the corner of the screen (it all depends on the design of your smartphone) and select the New access point item. At the point being created, we write only two settings:

• Name - Tele2 Internet;
• APN - internet.tele2.ru (without http://).

We save the settings and try to access the Internet, after activating the data transfer. Also, in the smartphone settings, you need to register automatic or forced work in 3G networks. Do not want to suffer with manual settings? Call 679 and order automatic settings, which will be activated and saved.

How to enter Internet settings on Tele2 in iPhone

It all depends on the version of the operating system installed in the smartphone. If your iPhone is running iOS 7.x.x, you need to go along the following path: Settings - Cellular (here we turn on the toggle switches Cellular data and Enable 3G) - Cellular data network. If your smartphone has iOS version lower than 7.x.x, then the path will be as follows: Settings - General - Network - Cellular data network. Next, you need to register the APN access point - internet.tele2.ru (without http://), and leave the username and password blank. After that, you can try to launch the browser and open some site.

When making settings on phones and some smartphones, you need to be prepared for the fact that some items may be called differently.

How to get MMS Tele2 settings

Sending/receiving MMS is a service based on Internet access. And for it to work, settings will also be required. If they didn't come automatically, you need to call 679. After a couple of minutes, a message with MMS settings will come to your phone. Save, activate, reboot and use.

How to manually set up MMS on your phone

If automatic settings do not come or are not registered, you need to enter manual settings. Create a profile:

• Profile name - Tele2 MMS (the name can be anything);
• MMS server (Home page) - mmsc.tele2.ru (without http://);
• Proxy server - enabled (unlike Internet settings);
• IP address (proxy server) - 193.12.40.65;
• Port - 8080 for phones with WAP2, 9201 for old phones with WAP1;
• Connection type or channel - GPRS;
• APN (access point) - mms.tele2.ru (without http://);
• Username and password - leave blank.

After that, you need to try to send MMS - the network must know that your phone can receive and send MMS. Otherwise, instead of incoming MMS, your phone will receive SMS with links to view multimedia messages.

How to set up the Internet on a 3G and 4G Tele2 modem

As a rule, Tele2 modems are supplied already configured. But if there are no settings for some reason, then they need to be written manually.- for this, a profile with an arbitrary name is created (for example, Tele2 Internet), the dial-up number *99# and the access point internet.tele2.ru are indicated, the username and password remain empty. We save the profile, set it as the default profile and try to establish a connection.

Articles and Lifehacks

Beeline's automatic Internet settings make life much easier for many users. And if you decide , you don't have to manually enter the required values, worrying if all the characters are spelled correctly.

If you are a subscriber of the Beeline network, then the Internet is connected in your device by default, according to the tariff that you chose when you issued a SIM card. Therefore, you do not need to perform any special actions.

If for some reason you turned off the Internet on your device, then to resume its work, dial the following combination on your phone: *110*181#. You can also do this by calling the operator.

How to get automatic settings

After a few seconds, the settings will be sent to your phone. You will only have to save the received data.

Set up Internet Beeline on the site

1. Find the "Phone settings" section
2. Select a device from the list. You can also enter the name manually.
3. Select the "Mobile Internet" service and check the status of the data connection on the phone.
4. Click on the line "Auto settings". There is also a manual setting function available here, but you don't need it yet.
5. Just below you will see a field where you will need to enter your phone number.
6. Click on "Send settings" and wait until the information arrives on your mobile device.
7. Save the received settings.

• The APN line should read internet.beeline.ru.
• The username is beeline.
• In paragraph Password should be beeline.

Usually customize Mobile Internet it is not necessary, since the connection occurs during the first initialization with a SIM card, and the settings come automatically. But don't hope for it. All the same, there are failures, due to which you yourself have to manually prescribe the settings for the mobile Internet. For self-configuration, all data can be found on the Beeline operator portal, as well as through the support service.

How to set up Beeline mobile Internet on a phone or tablet?

As mentioned above, on your mobile device, the Internet can be installed automatically in automatic mode, or manual configuration is still required. Depending on the device model you are using. For most new devices (phones, tablets), automatic settings, if they did not come by themselves, can be ordered from the official website using your computer, or dial a special service number on the device.

Before setting up mobile Internet on your device, you should find out if the "Pack of three services" service is activated. To check it you should dial the service number 067409 . After submitting the application, you will receive a full list of connected services on your phone in the form of SMS. If this service is not connected to you, you should connect it to access the Internet. Send service USSD command: *110*181# .

Automatic Internet setup Beeline

To receive automatic Beeline Internet settings on your phone, you should go to the website of the Beeline operator. On the official portal, go to "Phone settings", in the window that opens, specify the type and name of the device you are using, as well as its model. Next, specify the "Mobile Internet" item, in which you will find out the system's ability to send you automatic settings for accessing the global network to your device.

If there are automatic settings for your device, you should enter your number in the appropriate field, to which the Beeline Internet settings will be sent. If you find yourself in a situation where the computer is not at hand, then the settings for the Internet can be obtained by ordering a service number 0611 and follow the prompts of the system. There is another way to request automatic settings for Internet access. By dialing a special number 0117 and having received automatic settings for accessing the Internet, you should save them with a subsequent reboot of the device.

Manual Internet setup Beeline on the phone

The table below shows the items with settings for self-entry into the device. Items that are not listed here should not be filled in. Leave them as they are by default on your device.

• Name Beeline Internet
• APN internet.beeline.ru
• Login beeline
• Password beeline
• IPv4 network type
• PAP authentication type
• APN default type

In most devices, even with various types operating systems Beeline Internet settings are practically the same.

Internet settings Beeline on Android

To configure the Internet in this type of device, go to the "Settings" section, then to the "Other networks" tab. In the dialog box that opens, select the "Mobile networks" tab. Check the box next to "Mobile Data". Next, you need to go to the "Access Points" tab. In this tab, to add settings, click the appropriate "Add (+)" button and enter the settings that were presented above. After entering, save them. Next, return to the "Access Points" tab and indicate the profile you just created, through which you will subsequently access the Internet. Below are all the sequential steps of creating a profile in the form of a screenshot, as well as a video at the end.

Beeline Internet settings on Windows Phone

In this type of device, you will need to go to the "Settings" of your device, and then go sequentially to the tabs: "Personal configuration" - "Adding a new one" - "Internet", here fill in all the lines from the table above, remembering to save the result. After saving the profile, we return to the "Settings" section. Next, select the "Configuration" tab - "Standard configuration settings" - "Personal configuration" - "Functions" - and then select the "As standard" profile you saved.

Beeline Internet settings on iOS (iPhone, iPad)

In these devices, manual configuration is much easier: go to "Settings" - "Cellular data" - then move the system slider to the "On" state. Next, go to "APN Settings" - here also enter the manual settings presented above in the table. After you have entered the settings, you need to save them, and in order for them to be activated, sometimes you may need to restart your mobile device. Next, to access the Internet in the menu, turn on "Data Transfer".

But still, there are cases when the user himself cannot configure his device. In a particular situation, the service number will help you 06503 , to which the system will respond by sending you detailed instructions by setting.

Now it is almost impossible to imagine a subscriber who would not use mobile Internet. But sometimes even a simple connection to the World Wide Web can cause difficulties. The only solution to this problem will be the correct configuration of the MTS Internet.

The operator has tried to make access to your favorite sites as simple and convenient as possible, so that any, even the most inexperienced and unprepared user, can cope with the difficulties that arise.

And in the most difficult situations, when the recommendations and instructions of the mobile company do not help, you can contact the contact center consultants. They will help you connect the mobile Internet and explain how to make settings on your own. As a result, customers will have to replenish the balance in a timely manner and just enjoy visiting their favorite sites.

There are several basic methods for setting up MTS Internet on your phone. Subscribers interested in connecting to the global network are able to:

• request suitable parameters using a special command;
• perform the operation yourself, manually making changes to the conditions for accessing the network.

At the same time, it should be clarified that the use of the second approach depends on the type of operating system installed on the smartphone.

Owners of iPhones and Android devices will have to perform different actions. Devices using Windows Phone also have their own settings.

Another important nuance that you need to remember is the existence of a special option that allows you to avoid the difficulties of preparing mobile phones for work. This option is present by default in all tariff plans, but can be disabled at the request of users.

Automatic Internet settings MTS

The easiest way to get your cell phone ready for use is to get automatic settings. Those who do not know how to order Internet settings on MTS should do the following:

1. the first step is to visit the official portal of the mobile operator and go to the "help" section;
2. in it you will have to switch to a subsection dedicated to the mobile Internet;
3. and select the item offering to order settings;
4. after loading a new tab, it remains to specify the phone where the message will be sent;
5. pass a test for a robot by selecting the appropriate pictures;
6. press the button labeled "send".

After that, it remains to wait for the complete completion of the procedure and make sure that the network connection has become available. In case of unforeseen difficulties, you should set up access yourself or contact the company's consultants.

How to get MTS Internet settings on your phone via SMS?

It is important to clarify that possible difficulties with automatic configuration via SMS will not prevent users from visiting their favorite sites. It has already been mentioned above that there is a special “access without settings” option that allows you to use the Internet without additional actions.

Since 2010, it has been included in the basic package of services of any tariff plan MTS and does not require connection. The exception is cases when the subscriber has deactivated this service independently, and now wants to make it active again. This will require:

• dial a special USSD request *111*2156# and press the dial key;
• send a short SMS message 2156 to a special service number 111 (disconnection is made by the message 21560);
• by connecting in the personal account of the subscriber on the official portal of the company.

The option is free and will not lead to additional expenses.

How to set up MTS Internet on Android?

Those who wish to set up MTS Internet on an Android phone will need to perform a number of simple steps:

1. enter the smartphone menu and select the item with the mention of "settings";
2. open the "wireless" subsection;
3. activate the mobile Internet and switch to the "mobile networks" subsection;
4. stop at the “MTS Internet” option or create an APN connection;
5. specify MTS Internet in the name line, enter in front of APN internet.mts.ru use the words mts as the login and password;
6. leave other parameters unchanged;
7. save the result.

In case of difficulties, you must additionally select the item “no” as the type of authentication. In case of other difficulties, you will have to seek support from specialists who will immediately correct the errors and set the appropriate parameters.

Internet setup on iPhone

Setting the correct parameters on iPhones looks a little different. To connect to the World Wide Web, you will need:

1. go to the settings menu;
2. select a special section "cellular communication";
3. switch to the parameters subsection;
4. open a tab with a mention of a cellular data network;
5. specify internet.mts.ru in the APN line;
6. enter the word mts in the login and password lines;
7. save your changes.

Additionally, users are able to manually configure the reception and sending of MMS. To do this, open the same section and enter the following conditions in the MMS settings:

• APN - mms.mts.ru;
• name and standard password - mts;
• MMSC - http//mmsc.ru;
• proxy - 192.168.192.192:8080.

As a result, there will definitely not be any difficulties with receiving messages.

Set up mobile internet manually

It is easiest for owners of other smartphones and phones to get the MTS Internet settings automatically. If the operator cannot send the correct parameters, you will have to prepare the device yourself. To do this, you will need to specify the same parameters that were used for devices on Android or iPhones. Phone owners will have to specify an access point, write down a password and clarify the network name.

If this procedure causes insurmountable difficulties, subscribers should contact support operators or visit the nearest branded communication salon. Managers working in it will help to cope with the existing difficulties.