This note is intended for novice cyclists and those who are going to buy a bike. Since this is not the first time I have received a question on how to raise the handlebars of a bicycle, I decided to write a few words about this.

I remember how, having bought my first bike, for a long time I could not understand how the steering wheel rises here, because on my Salute from childhood it was done elementarily. 🙂

Unfortunately, on modern bikes, the handlebar height is not directly adjustable. The absence of such a mechanism is a retribution for the simplicity of design and light weight.

Therefore, if you bought a new bike, then most likely you will only be able to lower the handlebars, which is also sometimes required. Therefore, a few words about how the steering part of the bicycle is arranged.

This picture shows one of the types of the old type of steering columns (threaded). None of the normal manufacturers have installed this on their products for at least eight to ten years.

But the wild Chinese, sold in stores like Auchan, is often equipped with just such a design. As a “nice” bonus, you will get the fact that you cannot put a working suspension fork on such a headset, because they have a different standard and rod diameter.

And here is what the steering part of a modern bicycle looks like. The extension is removed by unscrewing the upper bolt securing the cover and those two bolts that, in fact, hold the system together.

There are several spacer rings under the stem. If the steering wheel needs to be lowered, then the rings are simply removed, the stem is installed back, the rings are put on top of it and all this is pressed on top of the lid. Please note that the bolt that secures the cover does not need to be tightened with all the dope.

Its role is to take up the slack and play of the steering column. After the steering is tightened with this bolt, align the steering wheel so that it looks straight, and tighten the mounting bolts. You need to tighten it conscientiously, but carefully and without fanaticism. This is what the steering part looks like with rearranged rings.

If the steering wheel needs to be lowered even lower, then the stem is turned over, as a result of which it begins to look down, and not up, as in the photo.

But if lowering the steering wheel is not such a difficult task, then raising it will require additional expenses. The easiest thing to do is to buy an adjustable stem, like this:

Keep in mind that stems come in different lengths, and if you need to raise the handlebar to a decent height, then buy a longer one. If your bike has a straight handlebar, then maybe it makes sense to replace it with a riser. In addition to being a few centimeters higher than the straight one, it is also more comfortable in taxiing, as it seems to me.

A more radical solution is to buy a tourist butterfly steering wheel. It can be lifted to a great height, in addition, a huge number of grips will help your hands at long distances.

To top it off, I would like to say to novice cyclists that the modern bike has a slightly different geometry than what we were used to as children. Do not immediately look for means of how to raise the steering wheel.

First, try to ride as it is. These bikes are designed to keep the handlebars low. Thanks to this landing, it is easier to give out decent speed, and most importantly - to ride for many hours in a row without experiencing back problems, because in this case the weight is effectively distributed between the arms and buttocks.

In most cases, people get used to in a few days, and later, if they feel like adjusting the steering wheel, then only in the direction of lowering. 🙂

Perhaps my readers will somehow supplement this note, all of a sudden, there are some other ways to raise or lower the steering wheel on a bicycle.

Friends, let's not get lost on the Internet! I suggest that you receive email notifications when my new articles are published, so you will always know that I have written something new. Please.

Often, the factory handlebar height settings are universal, and not specifically selected for certain person. Cyclists often experiment with saddle height, tire pressure, handlebar angle, and suspension settings, but few are aware of the benefits of adjusting handlebar height. The height of the handlebar is sometimes referred to as the position of the saddle relative to the handlebar, that is, the interval by which the seat is higher or lower than the handlebar.

For professional riders, this interval is usually significant, and the handlebars are lower than the saddle, while amateur cyclists do not. Simply put, a lower handlebar height lowers the center of gravity. By placing more weight on the front wheel, you increase traction. In addition, the low handlebar height allows the rider to be more centered between the wheels, improving the bike's handling, especially during uphill climbs. This effect is more noticeable off-road, mainly with 29-inch wheels.

Handlebars that are too low can make it difficult to steer the bike, so there is a limit. Luckily, experimenting with handlebar positions is easy and mostly free. This manual is suitable for owners of modern bikes with adjustable stems and a proper steering column. If the bike stem is bolted to the steering column, it is most likely adjustable.

• It will take time: 15 minutes
• Difficulty level: easily
• Price: is free

Required Tools

1. Universal set of bicycle tools or hexagons.
2. Adjustable torque wrench or torx wrench, especially when working with carbon or light materials.
3. Handlebar stems from Zipp, Ritchey and Syncros require Torx wrenches instead of hex keys, so T20 or T25 Torx wrenches may be needed.

Adjustment of spacer rings of a steering column

The first and easiest way to adjust the height of the steering wheel is to swap the steering column rings.

Headset rings fit over your bike's fork stem and help you adjust the handlebar and stem height. As a rule, the standard size of spacer rings is from 20 to 30 mm. They can be freely rearranged along the entire length of the stem. Removal bolts are twisted on general scheme(unscrew counterclockwise, screw clockwise).

1. First, firmly fix the wheels of the bicycle, after which you should loosen the clamps on the back of the handlebar stem. Now it's time to grease the bolt that secures the steering column cover a little so that it gives in more easily.

2. Unscrew the top bolt securing the cover,(it fits into the steering column anchor star nut) and set the cover aside.

3. Disconnect the steering column and stem from each other.

4. Now it's time to decide how high you would like to raise or lower the handlebars.. Depending on the decision made, you should add or, conversely, remove the required number of rings from the bottom of the steering column located under the steering wheel.

5. Then insert the steering column back into the stem mount, and move the freed rings that were previously located under the stem to the top of the fork stem above the stem.

Make sure that the distance between the upper edge of the ring and the fork stem is at least 3-5 millimeters, otherwise it will not be possible to securely fix the steering column without backlash.

6. Next, replace the steering column cover and tighten the bolt, but not too much to avoid the formation of backlash. Thus, you will pre-fix the structure.

7. Then align the stem so that it is in the same plane as the front wheel and at right angles to the handlebar. This step requires patience, but will allow you to adjust the position of the handlebars relative to the top tube of the bike frame.

8. Now that the stem is in the correct position with respect to the front wheel, tighten the stem bolts gradually and alternately using an adjustable torque wrench, typically 5 to 8 Nm.

9. It's time to check the takeaway settings. To do this, use a simple trick. Lock the front brake with one hand and place the other on the steering column, then turn the steering wheel slightly back and forth. Can you feel the fork stem moving inside the steering column? If so, you need to loosen the steering column fasteners and tighten the bolt on its cover more tightly, then tighten the fasteners again.

Repeat these steps until all signs of free play in the steering column disappear, and the steering wheel does not turn freely. If you tighten the bolts too much, you may have difficulty turning the steering wheel. If all else fails and your steering column is hard to adjust, it might be time to replace it.

10. Test the new handlebar height

Expand the stem

If the permutation of the rings did not fully satisfy the requests, we recommend resorting to one more trick. You can turn the stem to reverse side. For mountain bikes, this part is turned mainly up, that is, by turning the stem, you change the height of the steering wheel. The procedure is the same as before, but the steering wheel in this case is removed from the steering column.

11.Place the bike on a level surface and secure the wheels firmly.. Remember at what angle the steering wheel and brake lever were located.
Loosen the bolts connecting the handlebar to the stem. Remove the front stem cover and set it aside in a safe place.

12. Carefully set the handlebars aside, then follow the lantern replacement procedure in steps 1-4.

13. After detaching the stem from the bike body, turn it the other way and insert it back into the fork stem.

14. Install the steering wheel in place, maintaining the same angle of the brake lever and the steering wheel itself.. Lock the stem front cover with the manufacturer's recommended torque (usually 4 - 8 Nm). Make sure all bolts are tightened evenly and spacing between stem fasteners is the same everywhere. If the gaps are uneven, the functionality of the steering wheel will be impaired.

Now follow the procedure for tightening the steering column and carrying out the steering wheel, set out in paragraphs 3-7.

So, it's time to test the new handlebar height in action. Adjusting the steering wheel height for a specific person takes some time. But the result is worth the effort. If the setup was successful, you will unlock the full potential of your bike.

Bicycle steering column maintenance - video

It may be necessary to adjust the handlebar height. You can raise the bike handlebars different ways, in order to do this you need to determine what type you have.

How to raise the handlebars on a bike

Threaded steering column

In order to raise the handlebars of a bicycle with a threaded steering column, do the following:

1. Loosen the central steering stem bolt, but do not unscrew it completely, otherwise the wedge-lock will come off;
2. Set the steering wheel to the required height and align with the front wheel;
3. Tighten the center bolt. Please note that after tightening, the structure should not stagger, move up and down, and there should be no backlash.

Threadless steering column

If your bike has a threadless steering column, then you can use the following methods to raise the steering wheel:

1. Install another , which has a higher lift. You can also install an adjustable stem, then you can change the height of the steering wheel at any time;

Change on a fork with a longer stem. In this case, you will need to purchase spacer rings of the desired length.

2. Do not add spacer rings to the old fork, the handlebar in this case may come off the fork stem. Some bikes already have a stock fork stem length, in which case you just need to rearrange the rings under the stem;

3. Install another . Set the steering wheel with a high lift or with large quantity hand positions.

When installing the rudder, be careful, the anchor cover should only be tightened with a bolt, but do not tighten it with force. If the bolt is overtightened, it may break the armature. Also, the tighter the bolt is tightened, the harder it will be to turn the steering wheel. The bolt should be tightened until the play in the steering column disappears. The rudder side stem bolts should only be tightened after the anchor has been pulled in.

Designed for off-road driving, so the structures are made of high-strength materials. For convenient and comfortable movement, the posture of the athlete is important. In this regard, the question of how to raise the handlebars on a mountain bike worries everyone.

Correctly raising the handlebars on a mountain bike is very important. This is especially true for situations where it has been stored or stored for a long time. The higher the steering wheel is raised, the greater the load on the rider's muscles.

Adjustment options:

1. Normal or null the position is considered flush with the saddle of the bicycle. This position is suitable for leisurely walks.
2. Position below the saddle but lowers the body of a person, makes the pose more streamlined, which reduces the resistance of oncoming flows.
3. Position above the saddle called high.
4. Centering. The steering wheel must be perpendicular to the front wheel.

Worth knowing! An important factor in height adjustment is the height of the rider. For people with a height difference of 20-30 cm, a different handlebar height will be required.

Height adjustment

Important! Adjustment according to these parameters is carried out for threadless bicycles. Models with a threaded axle are monolithic and only allow vertical movement.

To change the angle of inclination, you must:

• loosen the fixing bolts;
• choose the optimal angle of inclination;
• fasten the mount.

An important issue for threadless fastening is the takeaway. Mechanics distinguish 3 types:

1. Vertical. Designed for height adjustment.
2. Horizontal. Compensates for the length of the bike frame
3. Angular. To install additional accessories and gadgets.

Saddle position

It is worth paying attention to the adjustment of the saddle. When the nose of the saddle is raised beyond measure, a person will fall back, when lowered down, he will slide. The optimal position must be selected based on the physique of the person.

The best option is the horizontal position of the saddle. Adjustment of the inclination of the saddle horizontally is carried out with the help of nuts, with which it is attached to the frame. After loosening the fixation, the most comfortable position is selected. Then, in this form, the saddle is fixed using previously loosened fasteners.

Important! When adjusting the saddle horizontally, it is assumed that the distance between the elbow and the fingertips should be equal to the gap from the front point of the saddle to the handlebars.

With the most insignificant skills, it is not difficult to solve the problem of setting up a bicycle according to your own parameters.

Video

It’s better to understand the question - how to raise the handlebars on a mountain bike will help the video.

Adjusting the steering wheel of a two-wheeled vehicle to personal needs is of great importance, since not only the comfort of the rider during movement depends on this, but also the maintenance of correct posture. Let's find out how to raise the handlebars on a bicycle, adjusting its position to personal needs.

Defining Moments

Before you figure out how to raise the handlebars on a bicycle, it’s worth understanding that not only its height adjustment matters, but also the centering relative to the wheel and hub.

It is necessary to decide in advance for what purposes the bike will be used. For example, driving on highways requires maximum control over the traffic situation. Therefore, the steering wheel in this case is set in such a way that the angle between the cyclist's back and the vertical is about 30 degrees.

How to raise the handlebars on a bike to ride at a walking pace? For young people, the landing angle here should be 45-60 about, and for the elderly - 60-90 about.

How to raise the handlebars on the bike In this case, the bike control tool should be located above the seat. For hybrid and mountain models, it is better to place the handlebar flush with the seat.

How to raise the handlebars on a children's bike?

The design of most bikes for kids suggests the possibility of adjusting the steering wheel not only in height, but also in tilt. This allows you to adjust the bike in such a way that riding takes place in the most comfortable and safe position for the child.

Usually, in order to raise the handlebars on a children's bike, it is enough just to loosen the central locking nut. If the child assumes a crouched position during boarding, move the control higher. When the baby hits the steering wheel with his knees, it is enough to change its inclination.

What tools might be needed to adjust the steering wheel?

Users who are trying to figure out how to raise the handlebars on their bike may need the following:

• a set of hex keys;
• tension limiters that will not allow stripping of the thread (especially useful when working with components made of lightweight materials);
• (for work with steering columns of the old type);
• for servicing specific steering stems, torxes - wrenches with a star-shaped head will be indispensable.

How to quickly change the handlebar height on a modern bike?

The easiest way to adjust the position of the bike control is to use specialized bikes. The latter often come with two-wheeled vehicles. If it is necessary to lower the stem lower, the conical rings can be removed from the vertical axis or replaced with a shortened spacer.

How to raise the steering wheel on a bike?

To adjust the position of the steering wheel, the following sequence of actions is performed:

1. To begin with, the front wheel of the bike is fixed. Then loosen the bolts that hold the stem to the steerer tube.
2. The steering column cover is removed. As a rule, 4-5 mm wrenches are suitable for this.
3. The stem is removed from the steering tube.
4. Next, you should decide how high you need to raise the steering wheel. Based on this, an appropriate number of spacer rings are put on the steering tube.
5. The steering stem is installed back, after which the steering column cover is put on top and the central fixing bolt is tightened to full resistance. Next, you should lift the bike by the frame and check how pliable all the components go.

Having figured out how to raise the handlebars on a bicycle, it is extremely important to align the stem so that it is in the same plane with the wheel. In conclusion, it is enough to test the convenience of controlling the bike with a new steering wheel height.

Particular attention when manipulating the steering column should be paid precisely to the level of clamping of the joints. Too little tightening will subsequently lead to damage to the bearings due to the occurrence of play. Excessively strong will affect the handling of the bike. The ideal tightening of the components is when the suspended wheel immediately leans to the side under its own weight.

In children, the musculoskeletal system is just being formed. How to raise the handlebars on a children's bike with a threaded or threadless headset?

How to raise the handlebars on a children's bike

So that the handlebars can be raised, parents buy a bike with a height and tilt adjustment function. Children should not touch its parts with their knees; for this, they also adjust the height and inclinations.

How to raise the steering wheel different types bicycles:

1. On the highway. On road bikes, the handlebars should be fairly low, whether it's intended for a child or an adult. Its valid location area is at the level of the saddle. This rule was established due to the fact that this body position is the most beneficial for fast driving. Some parents are not happy with the child riding in this position, and therefore they get a standard children's bike.
2. On forward brand bikes. The difficulty in adjusting the handlebars in bikes of this brand lies in the fact that it is much easier not to raise it, but to replace the stem with an identical one, but with a greater slope (or with a handlebar with a lift function). Some cyclists have adapted to change the position of the steering wheel on bikes of this brand with a nut.
3. On the mountain. The height of the steering wheel is identical to the road one - it should be located at the level of the saddle. To set the correct height on a mountain bike, you can use the adjustable bike stem. Be sure to take into account the position of the saddle, since there may be several combinations.

To adjust the height of the steering system, the steering wheel is first disassembled. There is no other way to change its position. The steering wheel of a children's bicycle is fixed on the sides with two bolts and in the center with one.

The central bolt eliminates the occurrence of play in the area of ​​the steering column. The remaining bolts fix the steering wheel at a certain height, and do not allow its position to change, so they are first unscrewed. Only after that the steering wheel can be moved to the required height.

Each children's bike on the steering system has limiter marks, beyond which the steering wheel cannot be installed. The same method is also suitable for lowering the steering wheel in some children's models. But often each steering system has a certain way of changing its position.

A semi-integrated column has a cup and bearing mounted inside the frame. If it is installed in a children's bike, there are restrictions regarding the rise, but you can lower it as low as possible. An integrated column for children's bicycles is rarely used. It is not equipped with cups, and is installed in the frame tube itself.

With threadless steering column

A threadless steerer tube is not threaded, and therefore the fork is installed with a spacer that is in the stem.

To change the position of the steering wheel in a bike with a threadless steering column, there is the following algorithm of actions:

1. First, choose a stem with a large lift or with a stem adjustment function. This is to change the height as needed.
2. Next, the factory plug is replaced with a new one. It should have a longer stem.
3. Attachment rings are purchased for the plug. Their installation will be outside.
4. After installing the steering system itself, slightly screwing the anchor cover, turn the steering wheel to the required position, and tighten all the bolts.

If it is not possible to purchase a stem with a large lift and replace the fork, then you can increase the height of the steering wheel with a threadless steering column as follows:

• unscrew the anchor bolt with a hexagon (some call it a “cover”, located in the upper part of the pipe);
• unscrew the tightening bolts;
• slowly and carefully remove the steering wheel and stem;
• install additional spacer rings on the pipe (they can be removed to lower the level of the steering wheel);
• complete the work by installing the stem, tightening the tie and anchor bolts, without overtightening the steering wheel to prevent mechanical damage to parts.

Since the structure can be displaced when changing the position of the steering wheel in this way, it is necessary to change its direction and removal, aligning them with the front wheel. If you find an uneven position, you can slightly loosen the bolts in the stem area, set the correct direction, and tighten them again.

With threaded steering column

At the threaded column, the fork is held with the help of an internal thread in the upper region of the cup and locknut. Inside the pipe there are two cups with ball bearings held by the puck. This type of mount is used on children's and adult professional bikes. Their manufacturers use a threaded column to reduce the weight of the bike, but it is more common in very cheap bikes.

The steering tube is installed inside the threaded column and tightened with bolts. When adjusting the height of the steering wheel, you need to be careful - you can get dirty with grease located in the mechanism area.

The algorithm for increasing the height of the steering wheel with a threaded column consists of the following steps:

1. First loosen the fixing nut at the bottom above the frame.
2. If necessary, the same operations can be performed with the lock nut.
3. Raise the steering wheel to the required height, in some cases an extension is required.
4. The work is completed by tightening the fixing and lock nuts.

Other actions with the handlebars on the children's bike

In some situations, you need to lower or tighten the handlebars of a children's bike. How to do it?

Lower

The steering part has a cover, bolts and spacer rings. To remove the stem, unscrew the top bolt holding the cover, and 2 bolts that secure the entire steering system. It is under the stem that there are spacer rings. To lower the steering wheel:

• remove rings;
• set the takeaway;
• removed rings are thrown over it;
• fix with a cover (the bolt can not be tightly tightened).

After tightening the steering column, the steering wheel is aligned with the front wheel, and the fixing bolts are tightened. If necessary, lower the steering wheel even lower, the stem turns over.

Tighten

It is necessary to tighten the steering wheel not only in order to lower or raise it, but also in case of its scrolling. In order to tighten the handlebars on a children's bike, you will need a set of hexagons.

It is highly discouraged to buy a set of cheap hexagons - such tools are often quickly cramped. It is better to buy steel hexagons in a specialized bicycle shop,

Take off

To completely remove the steering wheel on a children's bike, you need:

• unscrew the bolts securing the steering wheel until the structure weakens;
• if it does not weaken, unscrew the bolts until the departure is at least 4 cm;
• clamp the front wheel of the bike with your feet, and slowly and carefully turn the steering wheel until it is completely removed.

List of required tools

Add to list necessary tools to remove or change the position of the steering wheel includes:

• a set of steel hexagons for unscrewing the steering wheel;
• you can purchase a set of TORX keys if the appropriate bolts are installed in the steering system;
• magnetic saucer - with its help, bolts and other metal objects placed in it will not be lost.

Thanks to these tools, the process of changing the position of the steering wheel is improved. In conclusion, it should be noted that the geometry of the bicycles that parents rode in childhood is significantly different from those that modern children's bikes have.

And not all situations require a change in the position of the steering system. Therefore, if in doubt, it is better for parents to consult with specialists.

Raise the steering wheel on a children's bike

With the onset of warm days, many cyclists appear in city parks and yards, most of whom are children. Well, among the vehicles on which they ride, the most popular is the Stels bicycle, on the handlebars of which there are soft pads, and the chain is securely protected. Under the growth of the child, the design can be adjusted by pulling out the seat and raising the handlebars on the stels bike.

Bicycles for children of the Stels brand meet the requirements of the market and are a high-quality product. Their advantages are simplicity, convenience and lightness. In order for the bike to grow together with the baby, it is enough to lift the saddle of the stels bike and the handlebar.

Transport for a small passenger has only the necessary functions. The manufacturer produces them in several colors so that you can choose a two-wheeled vehicle for a boy and a girl. For each age, the bike is selected with the appropriate wheel diameter.

The company produces transport for children and adults, classic and folding models, the advantage of which, in comparison with the bikes of the Soviet era, is that it does not need to be used for folding. great strength: it is enough to move aside and slightly raise the eccentric.

In the line of the domestic company, there are various models that differ from the products of other manufacturers in rich equipment and adequate prices: all bicycles are equipped with luggage racks, metal fenders, footrests and side wheels, and a horn.

Pedal foot braking is the best for little cyclists, but there is also a handlebar-mounted brake on the bike, which allows you to get used to manual braking.

Raising the handlebars on a kid's bike is as easy as adjusting the angle so that a young rider can ride comfortably.

A properly adjusted handlebar is an important condition that affects riding comfort and maneuverability. If driving a two-wheeled vehicle is easy, you can be sure of the safety of the child.

When adjusting the steering wheel, one should not forget that there is a close relationship between its height and the saddle and that a steering wheel set too low negatively affects the bike’s handling, since the center of gravity of the bike shifts down, and the load on the front wheel increases and also grows. thrust.

Proper seating for baby

Specialists for children to ride bicycles. This will only benefit the health of the baby. But, since a figure is formed at this age, it is important that the position of the child's body during skating is correct.

To fulfill this requirement, you need to select a bike strictly in accordance with the height of the child. A bike that is too small or bought “for growth” can harm a child instead of good.

As the baby grows, it is advisable to choose models with an adjustable seat and steering wheel. The child should not touch the steering gear with his knees. But too much tilt of the body is unacceptable.

These children's models are convenient and safe for the child.

The bike uses a threaded type of head tube, i.e. the latter is inserted inside the steering column and secured with a central fixing nut.

This lock nut must be loosened if you need to lower or raise the handlebars of a children's bike. Use the key for this. After this action is completed, the steering tube is set to the desired height and the lock nut is tightened.

To adjust the tilt, you need to unscrew the coupler bolts and, turning the handlebar back / forward, set the desired angle.

Important: when raising or lowering the steering wheel, watch the cables so that they do not get tangled, by changing the tilt of the steering wheel, check whether the landing has become comfortable. If not, try adjusting the seat.

With such a friend, every child's childhood will be happy and full of adventure. It will help from an early age to keep a sense of balance, overcome obstacles, communicate with peers.

Video: How to raise the handlebars on a bicycle

It may be necessary to adjust the handlebar height. You can raise the handlebars of a bicycle in various ways, in order to do this you need to determine what type you have.

How to raise the handlebars on a bike

Threaded steering column

In order to raise the handlebars of a bicycle with a threaded steering column, do the following:

1. Loosen the central steering stem bolt, but do not unscrew it completely, otherwise the wedge-lock will come off;
2. Set the steering wheel to the required height and align with the front wheel;
3. Tighten the center bolt. Please note that after tightening, the structure should not stagger, move up and down, and there should be no backlash.

Threadless steering column

If your bike has a threadless steering column, then you can use the following methods to raise the steering wheel:

1. Install another , which has a higher lift. You can also install an adjustable stem, then you can change the height of the steering wheel at any time;

Change on a fork with a longer stem. In this case, you will need to purchase spacer rings of the desired length.

2. Do not add spacer rings to the old fork, the handlebar in this case may come off the fork stem. Some bikes already have a stock fork stem length, in which case you just need to rearrange the rings under the stem;

3. Install another . Install a handlebar with a high lift or more hand positions.

When installing the rudder, be careful, the anchor cover should only be tightened with a bolt, but do not tighten it with force. If the bolt is overtightened, it may break the armature. Also, the tighter the bolt is tightened, the harder it will be to turn the steering wheel. The bolt should be tightened until the play in the steering column disappears. The rudder side stem bolts should only be tightened after the anchor has been pulled in.

Designed for off-road driving, so the structures are made of high-strength materials. For convenient and comfortable movement, the posture of the athlete is important. In this regard, the question of how to raise the handlebars on a mountain bike worries everyone.

Correctly raising the handlebars on a mountain bike is very important. This is especially true for situations where it has been stored or stored for a long time. The higher the steering wheel is raised, the greater the load on the rider's muscles.

Adjustment options:

1. Normal or null the position is considered flush with the saddle of the bicycle. This position is suitable for leisurely walks.
2. Position below the saddle but lowers the body of a person, makes the pose more streamlined, which reduces the resistance of oncoming flows.
3. Position above the saddle called high.
4. Centering. The steering wheel must be perpendicular to the front wheel.

Worth knowing! An important factor in height adjustment is the height of the rider. For people with a height difference of 20-30 cm, a different handlebar height will be required.

Height adjustment

Important! Adjustment according to these parameters is carried out for threadless bicycles. Models with a threaded axle are monolithic and only allow vertical movement.

To change the angle of inclination, you must:

• loosen the fixing bolts;
• choose the optimal angle of inclination;
• fasten the mount.

An important issue for threadless fastening is the takeaway. Mechanics distinguish 3 types:

1. Vertical. Designed for height adjustment.
2. Horizontal. Compensates for the length of the bike frame
3. Angular. To install additional accessories and gadgets.

Saddle position

It is worth paying attention to the adjustment of the saddle. When the nose of the saddle is raised beyond measure, a person will fall back, when lowered down, he will slide. The optimal position must be selected based on the physique of the person.

The best option is the horizontal position of the saddle. Adjustment of the inclination of the saddle horizontally is carried out with the help of nuts, with which it is attached to the frame. After loosening the fixation, the most comfortable position is selected. Then, in this form, the saddle is fixed using previously loosened fasteners.

Important! When adjusting the saddle horizontally, it is assumed that the distance between the elbow and the fingertips should be equal to the gap from the front point of the saddle to the handlebars.

With the most insignificant skills, it is not difficult to solve the problem of setting up a bicycle according to your own parameters.

Video

It’s better to understand the question - how to raise the handlebars on a mountain bike will help the video.

This note is intended for novice cyclists and those who are going to buy a bike. Since this is not the first time I have received a question on how to raise the handlebars of a bicycle, I decided to write a few words about this.

I remember how, having bought my first bike, for a long time I could not understand how the steering wheel rises here, because on my Salute from childhood it was done elementarily. 🙂

Unfortunately, on modern bikes, the handlebar height is not directly adjustable. The absence of such a mechanism is a retribution for the simplicity of design and light weight.

Therefore, if you bought a new bike, then most likely you will only be able to lower the handlebars, which is also sometimes required. Therefore, a few words about how the steering part of the bicycle is arranged.

This picture shows one of the types of the old type of steering columns (threaded). None of the normal manufacturers have installed this on their products for at least eight to ten years.

But the wild Chinese, sold in stores like Auchan, is often equipped with just such a design. As a “nice” bonus, you will get the fact that you cannot put a working suspension fork on such a headset, because they have a different standard and rod diameter.

And here is what the steering part of a modern bicycle looks like. The extension is removed by unscrewing the upper bolt securing the cover and those two bolts that, in fact, hold the system together.

There are several spacer rings under the stem. If the steering wheel needs to be lowered, then the rings are simply removed, the stem is installed back, the rings are put on top of it and all this is pressed on top of the lid. Please note that the bolt that secures the cover does not need to be tightened with all the dope.

Its role is to take up the slack and play of the steering column. After the steering is tightened with this bolt, align the steering wheel so that it looks straight, and tighten the mounting bolts. You need to tighten it conscientiously, but carefully and without fanaticism. This is what the steering part looks like with rearranged rings.

If the steering wheel needs to be lowered even lower, then the stem is turned over, as a result of which it begins to look down, and not up, as in the photo.

But if lowering the steering wheel is not such a difficult task, then raising it will require additional expenses. The easiest thing to do is to buy an adjustable stem, like this:

Keep in mind that stems come in different lengths, and if you need to raise the handlebar to a decent height, then buy a longer one. If your bike has a straight handlebar, then maybe it makes sense to replace it with a riser. In addition to being a few centimeters higher than the straight one, it is also more comfortable in taxiing, as it seems to me.

A more radical solution is to buy a tourist butterfly steering wheel. It can be raised to a great height, moreover, great amount grips will help hands at long distances.

To top it off, I would like to say to novice cyclists that the modern bike has a slightly different geometry than what we were used to as children. Do not immediately look for means of how to raise the steering wheel.

First, try to ride as it is. These bikes are designed to keep the handlebars low. Thanks to this landing, it is easier to give out decent speed, and most importantly - to ride for many hours in a row without experiencing back problems, because in this case the weight is effectively distributed between the arms and buttocks.

In most cases, people get used to in a few days, and later, if they feel like adjusting the steering wheel, then only in the direction of lowering. 🙂

Perhaps my readers will somehow supplement this note, all of a sudden, there are some other ways to raise or lower the steering wheel on a bicycle.

Friends, let's not get lost on the Internet! I suggest that you receive email notifications when my new articles are published, so you will always know that I have written something new. Please.

Instructions: Raise the handlebars on children's and adult bikes

In the understanding of many, adjusting the height of the steering wheel is not difficult, because it was so easy to do on all bikes in childhood. However, in modern bicycles it is impossible to change the position of the handlebars in the same simple way. This is explained by the fact that modern bike models have become much lighter and simpler in design. Therefore, do not be surprised if the position of the steering column is not quite easy to change on a new bike.

Consider, more closely, the steering part is great. A kind of threaded steering column is an old age. Currently, none of the bona fide manufacturers will allow such a part to be installed on the products of their brand. In the last 8-9 years, this trend has continued. But that doesn't apply Chinese manufacturers, often a similar design is still found among bicycles made in China. One of the annoying inconsistencies is that it is impossible to install a suspension fork on such a steering wheel (due to the difference in standards and stem diameter).

A set of necessary tools

In order to change the position of the steering wheel on your bike, you will need the following tools:

• Hexagons of various sizes, so the best option would be to have a whole set;
• Tension limiter. It will allow you to keep the threads in their original state when working with light components such as carbon;
• Torxes T20 and T25 (special type of keys). They may be needed for certain offset models.

The takeaway is quite easy to dismantle if you first unscrew the bolt that secures the cover, as well as a couple of bolts that hold the structure itself in the assembled state. The fastening sequence is as follows: first there is a removal, then special spacer rings are located.

If it is only necessary to lower the steering part, the rings are dismantled and the stem is returned to its original place, and the rings are placed on top of it, after which everything is fixed with a lid.

Attention! The bolt that is installed at the end, fixing the cover, is not advisable to tighten too much. His participation in the design comes down to removing possible slack, as well as play at the steering column.

After fixing the steering part with a bolt, you need to align the steering wheel itself and finally fix the system with bolts. Tighten the mounting bolts carefully, without applying excessive force, but at the same time, conscientiously.

Sometimes there is a need for the reverse process - the steering wheel must be lowered. To do this, you need to turn the stem so that it looks down. Remember that lowering the steering wheel is much easier than raising it. It is possible to facilitate this procedure by purchasing a special stem that can be adjusted.

Takeaways are presented in different options, differing in length. The pattern is simple: if you want to raise the steering wheel to a considerable height, opt for a longer stem model.

Height adjustment value

In order for riding to bring you pleasure and comfort, you must feel as comfortable as possible in the process. This is why adjusting the handlebar height and stem is so important. Experts confidently state that the inability to adjust the steering wheel height directly affects its maneuverability and comfortable riding. It is difficult to control a bicycle, which means that there is no way to be sure of your absolute safety. There can be countless combinations in the settings of your bike, so feel free to experiment with the level of saddle height, suspension condition, tire pressure. But do not neglect such an important factor as the correct installation of the steering wheel in height.

There must be a relationship between the heights of the steering wheel itself and the saddle. For example, professional riders often set the handlebars lower than the saddle level. Those who choose a comfortable and relaxed style of travel, raise the steering wheel higher.

Note! A handlebar that is specially adjusted and set low greatly reduces the degree of control of the bike and the likelihood of full control over the situation in the process of movement.

Your bike's center of gravity drops if the handlebars are low enough. That is why the load on the front wheel increases, and, accordingly, traction. Also, the advantages include a more even distribution of weight between the two wheels, this is beneficial for mountain climbs. Such effects are especially noticeable on bicycles with large diameter wheels. You can try on different handlebar heights and compare the feel of each new position, choosing the best one for free and without the help of specialists.

When a cyclist is moving on roads, it is recommended to keep the back angle of about 30 degrees. If the riding style is quite active, the back angle is desirable in the range of 45 to 60 degrees. For the elderly, as well as children, you should stop at the angle parameter of 60-90 degrees.

Tag Cloud:

how to raise the handlebars on a mountain bike