Articles and Lifehacks

Beeline's automatic Internet settings make life much easier for many users. And if you decide , you don't have to manually enter the required values, worrying if all the characters are spelled correctly.

If you are a subscriber of the Beeline network, then the Internet is connected in your device by default, according to the tariff that you chose when you issued a SIM card. Therefore, you do not need to perform any special actions.

If for some reason you turned off the Internet on your device, then to resume its work, dial the following combination on your phone: *110*181#. You can also do this by calling the operator.

How to get automatic settings

After a few seconds, the settings will be sent to your phone. You will only have to save the received data.

Set up Internet Beeline on the site

1. Find the "Phone settings" section
2. Select a device from the list. You can also enter the name manually.
3. Select the "Mobile Internet" service and check the status of the data connection on the phone.
4. Click on the line "Auto settings". There is also a manual setting function available here, but you don't need it yet.
5. Just below you will see a field where you will need to enter your phone number.
6. Click on "Send settings" and wait until the information arrives on your mobile device.
7. Save the received settings.

• The APN line should read internet.beeline.ru.
• The username is beeline.
• In paragraph Password should be beeline.

Alexander Grishin

If you don’t know how to order automatic Internet settings on Tele2, then take a couple of minutes to read this instruction. We will tell you how to get them, as well as what to do if the settings do not arrive or you cannot install them. The instruction is suitable for smartphones on different platforms: Android, iOS and Windows 10 Mobile.

Receiving automatic Tele2 settings

In order to receive automatic Internet settings on your phone with a Tele 2 SIM card, you need to make a request by dialing a short number 679 . After that, the operator should send the Internet/MMS settings almost immediately. Save them and restart your phone - the Internet should work.

If it does not work, then go to the settings section and check if the internet.tele2.ru access point is selected as the default access point.

check path:

• for smartphones on Android 5.1 (in earlier versions, the path may be different): Menu -> settings -> mobile network -> APN access points
• for Windows 10 Mobile: Menu —> settings —> network and wireless connections —> cellular network
• for Windows Phone: Menu —> settings —> network and wireless connections —> cellular network
• for iPhone: Menu -> settings -> main network -> cellular data network

If the automatic Tele2 Internet settings do not come, you will have to enter them manually

Manual Internet setup Tele2

You can manually configure the Internet on Tele 2 as follows:

1. Go to the menu and select the "Access Point" subsection. How to do this is written above.
2. Create a new profile and give it a name, for example “Tele 2 INTERNET”
3. In the APN (access point) field, write: internet.tele2.ru
4. In the MNC field, enter: 20
5. Enter in the MCC field: 250
6. In the APN Type field, select: default.
7. In the field of the home page, enter: http://m.tele2.ru
8. Proxy Server: Not set or Off.

You can leave all other fields blank. In the end it should look like this:

Save the settings, try to restart the Internet - it should work.

Manual settings parameters can also be ordered via SMS using the code *202# or find them on the official website of the operator.

P.s. if after automatic or manual setting Internet tele2 does not work, check if mobile Internet service (GPRS / EDGE) is connected to your tariff.

We hope we were able to help you. If you have any questions, ask them in the comments or our

Each phone connected to the Megafon network wonders how to set up the Internet? Without the correct settings, you will not be able to use the network and MMS. This applies to both conventional phones and massively used smartphones.

When you install a SIM card in any modern mobile device, it is configured automatically. However, sometimes it happens that the settings themselves were not installed or were not registered - then you need to set up the phone manually. This review will tell you how automatic tuning works, as well as how to enter the settings yourself.

Ordering Internet settings from Megafon

Using SMS commands, the user can get Megafon Internet settings for his phone. If you want to set up access, you must send to the number 5049 the number "1", after which an SMS containing the profile settings will be sent. You need to save them and activate the profile, then try to enter the network. On Megafon, GPRS settings are also available in the help desk, for this we dial 0500, name the model of the phone used and wait for a service SMS with settings.

By visiting the Megafon website, on it, in the Self-Service Services section, you can find another subsection with Mobile device settings, in which individual settings are ordered that are suitable for any mobile phone model. We select the phone brand, model, as well as the ordered data in the drop-down lists, below we enter the phone number used to send the required settings.

Internet settings Megafon manually

APN settings (or access points) on Megaphone can be done manually. To do this, a new profile is created on the phone containing the following data:

• Profile name: specify, for example, Megafon (absolutely any names are allowed here);
• Home page: type megafon.ru (you can also enter any address, since this setting concerns the home page used by the phone's built-in browser);
• Access point: drive in internet;
• Authentication: choose "normal";
• Login with password: do not need to fill.

There may also be settings for a proxy server, but it is recommended to disable the use of a proxy, you do not need to fill in any data here. After filling in the specified settings, by opening a browser, you can try to launch the Internet on your phone.

If you need to figure out how to set up the Internet on Megafon using 3G technology, then there is no need to make additional third-generation network settings, just go to the item called "Properties of mobile networks" and check that there is a search for a WCDMA network (or the forced registration function is set for WCDMA networks).

When making the above settings, remember that the menu item containing the Internet profile setting may be different depending on the specific smartphone model. In addition, there may also be differences in the names of the fields to be filled in, for example, "Access Point", as well as "APN" - this is a similar name.

Setting up MMS on Megafon

The procedure for setting up MMS for the Megafon operator is almost identical to ordering for the Internet. To get a working function that allows you to receive and send multimedia MMS messages, you need to send the number "3" to the number 5049. After a short time, the phone will receive a message containing the necessary settings: you need to save them, then apply and try to send MMS to any Megafon number. Similarly, automatic settings are ordered through the Megafon website, after selecting the phone model from the list provided.

Setting up MMS on your phone manually

In cases where you cannot accept automatic settings or install them, you will have to enter the settings manually. To do this, a profile is created on your phone, indicating the data below:

• Profile name: you can just dial MMS (you can enter anything);
• Server or home page address: specify http://mmsc:8002 (no change);
• Proxy: must be "enabled";
• Address for the proxy: we drive in the numbers 10.10.10.10;
• Port field for the proxy used: 8080;
• APN (or may be the name "Access Point"): mms;
• The user and password fields are not required.

As with setting up an Internet profile, depending on the smartphone you are using, some items may have different names.

Setting up the Internet on 3G (4G) Megafon modems

Such popular 3G and 4G modems offered by Megafon are usually sold with the settings already made: after purchasing the device, it connects to any USB port, after which you must wait for the installation to finish, which is launched automatically by the modem's control program. After that, everything is prepared for Internet access.

If the data that was present in the automatically created profile was lost, then you can manually configure the Megafon modem. To do this, you need to create a profile and the following is written in it:

• Profile name: specify any, for example, Internet Megafon;
• Access point or APN: internet;
• Number for dialing: dial *99# in the field;
• The username and password fields are not required.

Everything is ready to check if you have an Internet connection.

In order for a mobile phone to be able to access the Internet and send / receive MMS messages, it is necessary to register the appropriate settings in it. Without settings, access to the above services will not be possible. In principle, almost all modern phones are configured automatically - activating a new SIM card leads to an automatic ordering of settings that will only have to be applied. After that, just in case, you need to restart the phone so that the settings take effect as correctly as possible.

But sometimes it happens that the phone remains unconfigured. In this case, you need to make manual settings or order automatic settings from the network. In this review, we will analyze all the ways to make settings for accessing the Internet from Tele2. MMS settings will also be considered.

The easiest way to set up your phone is to order automatic Internet settings on Tele2. They will be accepted from the network and registered in the corresponding profiles. You can order Internet settings on Tele2 by calling 679- they will be received within a few minutes in the form of incoming SMS messages. After that, you can access the network using a built-in or downloaded browser from somewhere (for example, Opera Mini, which saves traffic).

How to manually set up the Internet on Tele2

If the Tele2 Internet settings for some reason are not accepted or not installed, manual settings should be registered. You do not need to give your phone into the hands of specialists and, moreover, pay money for it - you can set all the settings yourself, there is nothing complicated about it. To enter the settings, you need to create a network profile and register the following items there:

• Profile name - Tele2 Internet (you can enter anything);
• Home page - http://m.tele2.ru/
• Proxy - off (respectively, we do not enter any settings here);
• Connection type - GPRS;
• Access point (APN) - internet.tele2.ru (without http://);

If necessary, specify the created profile in the browser settings.

Some phones specify a profile for Java applications. If Internet access does not appear, the phone needs to be restarted. You will have to suffer with the settings of Chinese phones, since the names of the items there can be completely different.

How to set up Internet from Tele2 on Android

If the operating system version is 2.3 or lower, you need to go along the following path: Settings - Wireless - Mobile networks - Internet access points. After that, press Menu and select Create APN. Here we set the following settings:

• Name - TELE2 Internet;
• APN - internet.tele2.ru (without http://);
• MCC - 250;
• MNC - 20;
• APN type - default.

Other items should be left blank. Next, press Menu and Save, after which we try to go online. Don't forget to enable data transfer. Is your smartphone running Android 3.0 or higher? Then the settings will be different. We pass along the following path: Menu - Settings - More - Mobile network - Access points (APN). We call the menu with a button or a virtual button in the corner of the screen (it all depends on the design of your smartphone) and select the New access point item. At the point being created, we write only two settings:

• Name - Tele2 Internet;
• APN - internet.tele2.ru (without http://).

We save the settings and try to access the Internet, after activating the data transfer. Also, in the smartphone settings, you need to register automatic or forced work in 3G networks. Do not want to suffer with manual settings? Call 679 and order automatic settings, which will be activated and saved.

How to enter Internet settings on Tele2 in iPhone

It all depends on the version of the operating system installed in the smartphone. If your iPhone is running iOS 7.x.x, you need to go along the following path: Settings - Cellular (here we turn on the toggle switches Cellular data and Enable 3G) - Cellular data network. If your smartphone has iOS version lower than 7.x.x, then the path will be as follows: Settings - General - Network - Cellular data network. Next, you need to register the APN access point - internet.tele2.ru (without http://), and leave the username and password blank. After that, you can try to launch the browser and open some site.

When making settings on phones and some smartphones, you need to be prepared for the fact that some items may be called differently.

How to get MMS Tele2 settings

Sending/receiving MMS is a service based on Internet access. And for it to work, settings will also be required. If they didn't come automatically, you need to call 679. After a couple of minutes, a message with MMS settings will come to your phone. Save, activate, reboot and use.

How to manually set up MMS on your phone

If automatic settings do not come or are not registered, you need to enter manual settings. Create a profile:

• Profile name - Tele2 MMS (the name can be anything);
• MMS server (Home page) - mmsc.tele2.ru (without http://);
• Proxy server - enabled (unlike Internet settings);
• IP address (proxy server) - 193.12.40.65;
• Port - 8080 for phones with WAP2, 9201 for old phones with WAP1;
• Connection type or channel - GPRS;
• APN (access point) - mms.tele2.ru (without http://);
• Username and password - leave blank.

After that, you need to try to send MMS - the network must know that your phone can receive and send MMS. Otherwise, instead of incoming MMS, your phone will receive SMS with links to view multimedia messages.

How to set up the Internet on a 3G and 4G Tele2 modem

As a rule, Tele2 modems are supplied already configured. But if there are no settings for some reason, then they need to be written manually.- for this, a profile with an arbitrary name is created (for example, Tele2 Internet), the dial-up number *99# and the access point internet.tele2.ru are indicated, the username and password remain empty. We save the profile, set it as the default profile and try to establish a connection.

The main function of MMS is the exchange of multimedia: video, photos, audio files. Usually, on new smartphones, the standard settings are set and the phone works well with them. Sometimes, these parameters are reset, and you have to set everything manually. You will learn how to get the MMS settings for a megaphone from the operator or set up the MMS yourself with your own hands.

Automatic MMS settings on Megaphone

The easiest option is to get the settings from the operator. The provider itself will send the required SMS package, which will set the required parameters, which will take a minimum of time.

How to get automatic MMS settings on Megafon

The method is suitable for those who are not in a hurry. Activating the service is easy. You need to send an SMS message with the text MMS to the number 5049. If the option did not work, then you can call one of the additional numbers: 05049 or 05190. After that, an SMS with the desired configuration will be sent to the phone, which will set all the settings. After that, you should restart your phone.

It is worth remembering that the operator may charge an additional fee for this service.

Setting up MMS Megafon manually

Setting the settings yourself will not cause difficulties for the average user.

To set the MMS megaphone settings for Android, iPhone, Windows Phone, you need to follow these steps:

1. Go to settings

iPhone: Settings - Cellular - Cellular data connection;

Android: Settings - Wireless networks - Mobile network - Access point;

Windows: Settings - Data transfer - Add an Internet access point;

1. Enter parameters:

Access point: mms.mc;

Username: MMS;

Password: mms;

IP: 10.77.77.10;

Home URL: http://mmsc:8002;

Session: Permanent.

1. For further access to the Internet, you need to enable data transfer.

Being in the home region, sending MMS at the selected rate is free. In roaming you will have to pay for this service. In order not to accidentally spend money, it is worth temporarily deactivating the service. To do this, you need to send an empty request to *105*308*0# .